Abstract:3D-printing concrete exhibits anisotropy under static loads, owing to its unique additive manufacturing process, while its dynamic performance study is still insufficient. In particular, the dynamic properties of 3D-printing ultra-high performance fibre reinforced concrete (3DP-UHPFRC) have not been studied yet. Therefore, this study explores the characteristics of 3DP-UHPFRC under impact loads using the SHPB tests. Three impact velocities of 3.886, 6.026, and 8.538 m/s were studied in the tests. The impact process was recorded by a high-speed camera. The dynamic mechanical characteristics of 3D-printing ultra-high performance concrete (3DP-UHPC) without fibre, 3DP-UHPFRC and reference specimens were investigated in terms of fibre type, fibre content, preparation method, loading direction, and impact velocity. The characteristics of strain rate, dynamic compressive stress, dynamic increase factor (DIF), energy absorption capacity and failure process were evaluated. The findings of this study indicated that the degree of failure of 3DP-UHPC was similar in all directions, while the degree of failure of 3DP-UHPFRC in all directions was different. The degree of failure in the X-direction was the worst, followed in decreasing order by the degrees of failure in the Y- and Z-directions. At the same impact velocity, the elastic modulus and strain rate effect of the 3D-printing specimens exhibited anisotropic characteristics, owing to the different elastic modulus of the 3D-printing specimens in each direction. Furthermore, the specimens were more susceptible to deformation in the X-direction than that in the Y- and Z-directions. As the impact velocity was increased, the dynamic peak stresses for 3DP-UHPFRC were isotropic at the same impact velocity, owing to the strain rate effect. Finally, the DIF of the 3D-printing specimens was observed to be anisotropic, and in the X-direction the specimens exhibited the most significant strain rate sensitivity.

Explosion Resistance of 3D Printing Ultra-High Performance Concrete Based on Contact Explosion Tests

Investigation of the Internal Structure of Hardened 3D-Printed Concrete by X-CT Scanning and Its Influence on the Mechanical Performance.

The Impacts of Contact Explosions on Ultra-High Performance Reinforced Concrete Slabs: Experimental Study and Dimensional Analysis.

Experimental and Numerical Investigation of G-UHPC Based Novel Multi-Layer Protective Slabs under Contact Explosions

Mechanical Properties and Failure Mechanism of 3D Printing Ultra-High Performance Concrete

Compressive Behavior of FRP-confined 3D Printed Ultra-High Performance Concrete Cylinders

Investigation of Ultra-High Performance Concrete Slab and Normal Strength Concrete Slab under Contact Explosion

Triaxial compressive behavior of 3D printed PE fiber-reinforced ultra-high performance concrete

3D-printing ultra-high performance fiber-reinforced concrete under triaxial confining loads

Effect of Pore Structure on Durability and Mechanical Performance of 3D Printed Concrete

Characteristics of 3D-printing ultra-high performance fibre-reinforced concrete under impact loading

An Experimental and Numerical Study of Reinforced Ultra-High Performance Concrete Slabs under Blast Loads

Repeated penetration and different depth explosion of ultra-high performance concrete

Bending Performance of 3D Printed Ultra High-Performance Concrete Composite Beams

Microstructure and mechanical behaviour of 3D printed ultra-high performance concrete after elevated temperatures

G-UHPC slabs strengthened with high toughness and lightweight energy absorption materials under contact explosions

Effect of Spraying Polyurea on the Anti-Blast Performance of the Ultra-High Performance Concrete Slab

In-process reinforcing method: dual 3D printing procedure for ultra-high performance concrete reinforced cementitious composites

Study on anisotropy of 3D printing PVA fiber reinforced concrete using destructive and non-destructive testing methods

Mechanical and Microstructural Evolution of 3D Printed Concrete with Polyethylene Fiber and Recycled Sand at Elevated Temperatures

Effects of Coarse Aggregates on 3D Printability and Mechanical Properties of Ultra High Performance Fiber Reinforced Concrete