Abstract:This paper presented a power-efficient, relatively high voltage gain, high GBW (gain-bandwidth-product) operational amplifier (OPAMP) with a pole cancellation technique and adaptive common-mode (CM) bias circuit. A typical two-stage topology is adopted in the OPAMP prototype design while the 1st amplifier stage is in class-A mode for high voltage gain and the 2nd buffer stage is in class-AB mode for both large drive capability and additional voltage gain. In order to improve GBW and set appropriate CM voltages, an actively biased resistor–capacitor pair is inserted in between the two stages with the overall frequency response of the OPAMP nearly unaffected. Thus, a little increase in area and power consumption is traded for pole cancellation while adaptive CM bias circuits are introduced to critical current-biased transistors with the outcome of excellent CM voltage stability across all process, voltage, temperature corners. In order to verify the practicality of the proposed OPAMP, a fully programmable analog baseband IC is designed with three key blocks, including trans-impedance amplifier, LPF (low pass filter)/HPF (high pass filter)/PGA (programmable gain amplifier) hybrid bi-quads, test buffer and power supply management units, and its − 3 dB bandwidth with voltage gain is fully programmable. What is more, two class-AB power efficient PMOS-only buffers are designed to ensure input and output test adaptability. Fabricated in a 40-nm Bulk CMOS process, the chip prototype achieves an LPF's − 3 dB bandwidth of 28–35 MHz with 3-bit digital control and 1 MHz/step programmability, an HPF's − 3 dB bandwidth of 3–15 MHz with 3-bit digital control, and a voltage gain of 0–63 dB with 6-bit digital control and 1 dB/step programmability. With a 20 dB voltage gain, HPF corner at 3 MHz and LPF corner at 35 MHz, the measured output P −1 dB is 12.1 dBm@20 MHz, and the output IP3 is 21.1 dBm@20 MHz. The total current consumption is around 3 mA@1.5 V and 2 mA@2.5 V.

A 50 Db High-Gain Operational Amplifier Integrated with Metal-Oxide TFTs

High-speed and high-gain operational amplifier

A New High-Gain Operational Amplifier Using Transconductance-Enhancement Topology Integrated with Metal Oxide TFTs

High-Speed Operational Amplifier Based on 0.5 Μm CMOS Process

A Common Drain Operational Amplifier Using Positive Feedback Integrated by Metal-Oxide TFTs

A Performance Optimized Operational Amplifier Using Transconductance Enhancement Topology Based on a-IGZO TFTs

A Wideband Db-Linear VGA with Temperature Compensation and Active Load

A Wideband BiCMOS Variable Gain Amplifier with Novel Continuous Db-Linear Gain Control and Temperature Compensation

Design of Differential Variable-Gain Transimpedance Amplifier in 0.18 Μm SiGe BiCMOS

A Wideband Digital Variable Gain Amplifier with DC Offset Cancellation in SiGe 0.18µm BiCMOS Technology

A 6.512-GHz Balanced Variable-Gain Low-Noise Amplifier With Frequency-Selective Gain Equalization Technique

A Design of High Performance Operational Amplifier

A power-efficient high GBW operational amplifier with its analog baseband IC implementation in 40-nm CMOS technology

Low-Voltage Operated High DC Gain Amplification Stage Based on Large-Area Manufacturable Amorphous Oxide Semiconductor Thin-Film Transistor

Oxide TFT Frontend Amplifiers for Flexible Sensing Systems

Design of Low-Power/Low-Voltage High Gain Amplifier

A 0.8-3GHz 40dB dynamic range CMOS variable-gain amplifier

A 10 kHz bandwidth low-power active negative feedback front-end amplifier based on unipolar IZO TFT technology

A 1ghz, 56.7db Linear-in-dB CMOS Wideband Variable Gain Amplifier

Modeling and Designing of High-Gain, Wide-Band and Fast-Speed Operational Transconductance Amplifier

A 0.9V All Digital Synthesizable OPAMP with Boosted Gain and Widened Common Mode Input Range