Abstract:Dissimilar metal welds (DMWs) between high-Cr martensitic heat-resistant steels and nickel-based alloys with nickel-based filler metals are widely used in fossil-fired power plants. Reports of premature failures of DMW joints have attracted considerable attention as such occurrences in the field can lead to significant economic loss and safety issues. Moreover, a comprehensive understanding of the high-temperature performance of new types of DMWs is lacking. In this work, creep tests were conducted over a stress range of 140-260 MPa at of 600 and 620 'C. A shift in the fracture location with variations in stress was observed, with three typical failure modes. At high stress levels (240-260 MPa), the DMW fractured in the base metal (BM) of martensitic steel, accompanied by a large degree of plastic deformation. At intermediate stress levels (200-240 MPa), the DMW fractured in the fine-grained heat-affected zone (FGHAZ) and the inter-critical heat-affected zone (ICHAZ), with creep cavities around coarsened carbides, indicating a typical type IV crack. At low stress levels (140-200 MPa), the DMW fractured in a mixed mode involving three stages. First, a crack initiated at the interface between the nickel-based weld metal and the martensitic steel, which was attributed to the interaction between the oxidation behavior of the martensitic steels and the thermal stress arising from the mismatch in the coefficients of thermal expansion. Second, the crack deflected into the FGHAZ/ICHAZ and developed into a type IV crack mode. Finally, the crack propagated into the adjacent BM, featuring significant plastic deformation. In addition, in the stress-LMP (Larson-Miller parameter) plot, the creep life at a relatively low stress level was shorter than that predicted by linear extrapolation of the data obtained at a high stress level, indicating a premature failure tendency at low stress. This premature failure tendency can be attributed to microstructure degradation in HAZs and preferential oxidation at the interface at low stress levels.

Near-threshold Fatigue Crack Growth Behavior of the Weld Metal and Heat-Affected Zone in an Ex-Service CrMoV Steel Joint

Near-threshold fatigue crack growth behavior of 10% Cr martensitic steel welded joint with 9% Cr weld metal in high temperature air

Low Cycle Fatigue and Creep Fatigue Interaction Behavior of 9Cr-0.5Mo-1.8w-v-nb Heat-Resistant Steel at High Temperature

Microstructure Characterization and HCF Fracture Mode Transition for Modified 9Cr-1Mo Dissimilarly Welded Joint at Different Elevated Temperatures

Effect of Temperature on High‐cycle Fatigue and Very High Cycle Fatigue Behaviours of a Low‐strength Cr–Ni–Mo–V Steel Welded Joint

HCF Failure Modes and Mechanisms of Dissimilar Welds of Martensite/Austenite Metals at Elevated Temperature

Very High Cycle Fatigue Behavior of 25cr2ni2mov Steel Welded Joint

Experimental Investigation of Fatigue Crack Growth Behavior of the 2.25cr1mo0.25v Steel Welded Joint Used in Hydrogenation Reactors

Effect of Carbon Migration on Interface Fatigue Crack Growth Behavior in 9cr/crmov Dissimilar Welded Joint

Very high cycle fatigue behavior of a low strength welded joint at moderate temperature

An Insight into the Creep-Fatigue Damage Localization in Welded Joints Based on Crystal Plasticity Finite Element Method

Fatigue Crack Growth Mechanism of Ni-based Weld Metal in a 9% Ni Steel Joint

Two Fatigue Fracture Modes at Different Temperatures of 10%cr Heat-Resistant Steel Weldment Filled with Ni-Based Alloy

High Cycle Fatigue and Fracture Behaviors of CrMoV/NiCrMoV Dissimilar Rotor Welded Joint at 280 °C

Effect of long-term aging on near-threshold fatigue crack growth of Ni–Cr–Mo–V steel welds

The Influence of Prior Austenite Grain Size on Fatigue Crack Growth Threshold of Welds in Cr-Mo-V Steel Components

Very High Cycle Fatigue Behavior And Life Prediction Of A Low Strength Weld Metal At Moderate Temperature

Microstructural Characteristics and Low Cycle Fatigue Properties at 230 °C of Different Weld Zone Materials from a 100 Mm Thick Dissimilar Weld of Ultra-Supercritical Rotor Steel

Transitional Behavior of Fatigue Crack Growth in Welded Joint of 25cr2ni2mov Steel

Failure Mechanisms and Design of Dissimilar Welds of 9%cr and CrMoV Steels Up to Very High Cycle Fatigue Regime

Fracture Location Shift of Dissimilar Metal Welds under Coupled Thermal-Stress Effect