Abstract:In the context of deep peak regulation, utility boilers are often required to operate at ultra-low loads, significantly deviating from their designed conditions, which can lead to unstable combustion or even furnace flameout. However, their operating characteristics at 20 % or even lower loads remain unclear. This study focuses on a 350 MW wall tangentially fired pulverized-coal boiler, exploring its combustion characteristics and pollutant emission patterns at 20 % ultra-low load. Through numerical simulation analysis of 14 different combustion scenarios, this research investigates the impacts of burner arrangements, burner horizontal swing angles (ranging from 5° to 20°), and methane (CH 4 ) co-firing ratios (ranging from 0 % to 20 %, calculated by heat value) on flue gas temperature and main flue gas components (O 2 , CO, NO x , etc.). The results indicate that as the boiler load decreases to 20 %, the average flue gas temperature inside the furnace drops by about 200 K, accompanied by widespread flame impingement on the water-cooled walls, leading to decreased combustion stability of the pulverized coal. Operating only the lower two layers of burners can achieve a higher average flue gas temperature (1540 K) and lower NO emissions (294 mg/m 3 ). Furthermore, setting the horizontal swing angle of the burners to 15° can mitigate the impact of flames on the water-cooled walls and elevate the flame center, with the average flue gas temperature reaching 1559 K, making it the recommended burner swing angle setting. As the CH 4 co-firing ratio increases from 0 % to 20 %, the average flue gas temperature rises by 50 K, and the emissions of NO and CO 2 decrease by 15.3 % and 6.2 %, respectively, while H 2 O concentration increases by 21.3 %, potentially leading to low-temperature corrosion issues. The recommended CH 4 co-firing ratio is 15 %.

Numerical Study of Slagging Trends in the Pre-Combustion Chamber at Swirl-Burner Outlet under Different Secondary-Air Temperatures

Study on the slagging trends of the pre-combustion chamber in industrial pulverized coal boiler under different excess air coefficients by CFD numerical simulation

Experimental Investigation of the Scaling-Off Location and the Slag Mass in Pulverized Coal-Fired Boiler with Water-Cooled Slag Removal

Theoretical and In-situ Experimental Investigation on Reducing Slagging Damage for Swirl-opposed Fired PC Boiler with Non-designed Blending Coals

Investigation on slagging and high-temperature corrosion prevention and control of a 1000 MW ultra supercritical double tangentially fired boiler

Flow Behavior of High-Temperature Flue Gas in the Heat Transfer Chamber of a Pilot-Scale Coal-Water Slurry Combustion Furnace

Influence of improving medium-speed pulverizer outlet temperature on the operation of boiler

Experimental research on the fire-carrying problems in primary air nozzle of 125 MW units

Investigation on Slagging Using Biased Secondary Air for Tangential Boiler

Influence of secondary air blade angle and oxygen-rich combustion characteristics of an improved Babcock swirl burner

An Effective Strategy for Monitoring Slagging Location and Severity on the Waterwall Surface in Operation Coal-Fired Boilers

Effect of swirl number on the number of particle impacts near a swirl burner outlet

Investigation on unsteady formation and evolution of high-temperature zone in a staged swirl combustor

Recirculating Structures and Combustion Characteristics in a Reverse-Jet Swirl Pulverized Coal Burner

Test Study Upon Slagging on the Heating Surface of Pulverized Coal Boiler

Effect of Operation Parameters on the Slagging Near Swirl Coal Burner Throat

Numerical investigation of stable combustion at ultra-low load for a 350 MW wall tangentially fired pulverized-coal boiler: Effect of burner adjustments and methane co-firing

97/03976 Researches on the aerodynamic characteristics of CWS tangentially arranged burners in utility boilers

Combustion Characteristics of Coal–Water Slurry in a Slag-Tap Vertical Cyclone Furnace Through Digital Imaging

Effects of coal particle size on the two-phase flow and slagging performance in a swirl burner

SLAGGING ANALYSIS AND PREVENTION OF UTILITY BOILERS WITH TILTING BURNERS