Abstract:Extensive experiments have shown that thin metal or metallic glass films usually rupture under a small tensile strain, which is extremely unfavorable for their engineering applications. The introduction of a highly deformable substrate with homogeneous microstructures can enhance the ductility of the films. However, the strong mechanical contrast between the substrate and the film usually induces interface debonding and premature cracks at the interface. Another disadvantage of the above film/substrate system is its significantly reduced strength due to the low strength of the homogeneous substrate. Recently, experiments have shown that a heterogeneous substrate with a grain size graded microstructure is able to provide an exceptional strength-ductility synergy in the film/substrate system. However, why does the graded substrate render such outstanding properties remains unsolved due to its complex microstructure. In order to answer this question, here a dislocation density-based constitutive model was incorporated into a finite element scheme to investigate the deformation of a thin film attached to a graded substrate. The deformation of the film on a normal substrate with a homogeneous grain microstructure was also analyzed for comparison. A V-shaped notch was adopted in the film to model its necking behavior based on a necking criterion. The necking strain is adopted as the tensile ductility. The results show that three typical deformation behaviors can be triggered by tailoring the microstructure of the graded substrate including the grain size of the topmost surface layer and the thickness of the grain size graded region. The three modes correspond to very different necking strains. Interestingly, the graded substrate with an optimal microstructure can provide the film with much higher necking strain than the homogeneous coarse-grained substrate could although the former itself is less ductile than the latter. In addition, the film/graded-substrate system possesses much better strength-ductility synergy than the film/homogeneous-substrate system. The enhancement of the tensile ductility results from the strong strain delocalization effect induced by the graded substrate. The predicted stress-strain responses are also compared with available experimental measurements. (C) 2019 Elsevier Ltd. All rights reserved.

Interfacial Behavior of Thin Film Bonded to Plastically Graded Substrate under Tensile Loading

Interface Behavior of a Thin-Film Bonded to a Graded Layer Coated Elastic Half-Plane

The Interfacial Behavior of an Axisymmetric Film Bonded to a Graded Inhomogeneous Substrate

The Interface Behavior of a Thin Film Bonded Imperfectly to a Finite Thickness Gradient Substrate

The Interface Behavior of a Thin Piezoelectric Film Bonded to a Graded Substrate

Nonslipping Contact Between A Mismatch Film and A Finite-Thickness Graded Substrate

Enhanced and Weakened Strength in Brittle Film-Substrate Structure

Tailoring Tensile Ductility of Thin Film by Grain Size Graded Substrates

Contact Involving a Functionally Graded Elastic Thin Film and Considering Surface Effects

An elastic-plastic cohesive zone model for metal-ceramic interfaces at finite deformations

Numerical Analysis of the Strength and Interfacial Properties of Adhesive Joints with Graded Adherends

Interfacial Delamination of Inorganic Films on Viscoelastic Substrates

Numerical Analysis on the Wrinkling Instability of a Stiff Film Adhering to an Elastic Substrate with a Graded Coating

Determination of the Interface Properties in an Elastic Film/substrate System

Effect of Substrate Deformation and Bonding Length on the Peeling Behavior

A Dislocation Dynamics Based Higher-Order Crystal Plasticity Model and Applications on Confined Thin-Film Plasticity

The Electromechanical Behavior of a Piezoelectric Actuator Bonded to a Graded Substrate Including an Adhesive Layer

The interfacial behavior of a thermoelectric thin-film bonded to an orthotropic substrate

On the Sliding Frictional Nanocontact of an Exponentially Graded Layer/substrate Structure

A Novel Thermal-Mechanical Model and the Characteristics of Interfacial Stress in the Laminated Structure for Flexible Electronics

Debonding Characterization of Stiff Film/compliant Substrate Systems Based on the Bilinear Cohesive Zone Model