Abstract:Titanium aluminide (TiAl) alloys are promising high-temperature structural materials in the aerospace field. Additive manufacturing is a desirable process for fabricating TiAl alloys. In the process of wire arc additive manufacturing of TiAl alloys, Al-based and Ti-based wires were used as the feedstocks. However, it is hard to ensure the two different wires melt synchronously under the heat of one single arc, so the desired microstructures with gamma (TiAl) phase and alpha(2) (Ti3Al) phase are hard to obtain. A two-wire TOP-TIG-based additive manufacturing process for TiAl alloys is proposed in this paper. The Ti6Al4V wire and pure Al wire are used as the feedstocks. The Al wire is fed in TOP-TIG mode behind the molten pool, while the Ti6Al4V wire is fed in conventional TIG mode in front of the molten pool. The two wires melt synchronously in a broad range of parameters. The compositions of the component can be controlled by adjusting the two-wire feeding speeds. The main microstructures of the as-fabricated component contain alpha(2)/gamma lamellae colonies, equiaxed gamma grains, and alpha(2) grains. In the top and middle regions, when the Al content is 45 at.%, the structures are full alpha(2)/gamma lamellae; as the Al content increases to 50 at.%, some equiaxed gamma grains distribute at the grain boundaries; the component with 55 at.% Al content exhibits the structures consists of equiaxed gamma grains with snowflake-shaped alpha(2)/gamma lamellae colonies. In the bottom region, all components exhibit the coarse equiaxed alpha(2) grains with gamma laths. As the Al content increases, the alpha(2) phase decreases, but the gamma phase increases, and from the top region to the bottom region, the volume fraction of the alpha(2) increases by about 19.4 %. The hardness value of the top and bottom regions is higher, and the middle region exhibits the lowest hardness. As the Al content increases, the hardness decreases. The component with 50 at.% Al exhibits the highest compressive strength with 1762 MPa and the largest compressive ratio with 26.1%.

Investigation on Heat Treatment Strategy Eliminating Heterogeneity and Anisotropy of TiAl Alloy Fabricated Using Twin-Wire Directed Energy Deposition-Arc

Microstructure Modification of Twin-Wire Directed Energy Deposition-Arc Fabricated Γ-Tial Alloy Via Deposition Current Control

Twin-wire Directed Energy Deposition-Arc of Ti–48Al–2Cr–2Nb Alloy: Feasibility, Microstructure, and Tensile Property Investigation

Modification of Microstructure and Mechanical Properties for Twin-Wire Directed Energy Deposition-Arc Fabricated Ti-48al-2cr-2nb Alloys Via Current Regulation

Effect of substrate temperature on microstructure and mechanical properties of TiAl alloy fabricated using the twin-wire plasma arc additive manufacturing system

Research on high efficiency deposition method of titanium alloy based on double-hot-wire arc additive manufacturing and heat treatment

Tailoring the mechanical properties and thermal stability of additive manufactured micro-alloyed Al-Cu alloy via multi-stage heat treatment

Heat Accumulation, Microstructure Evolution, and Stress Distribution of Ti–Al Alloy Manufactured by Twin‐Wire Plasma Arc Additive

High-Superelasticity NiTi Shape Memory Alloy by Directed Energy Deposition-Arc and Solution Heat Treatment

Effect of Heat Treatment on Microstructure and Tensile Properties of Ti-6Al-4V Alloy Produced by Coaxial Electron Beam Wire Feeding Additive Manufacturing

Fabrication of γ-TiAl intermetallic alloy using the twin-wire plasma arc additive manufacturing process: Microstructure evolution and mechanical properties

Influence of Local Thermal Cycle on the Lattice and Microstructure Evolution of Twin-Wire Directed Energy Deposition-Arc Fabricated Equiatomic NiTi Alloy

In-Situ Regulation to Tailor Additive Manufacturing of TiAl Alloy with Homogeneous Fine Fully Lamellar Colony

Composition fine-tuning for directed energy deposition of Ti-6Al-4V

Microstructure evolution and tensile property of TiAl alloy using continuous direct energy deposition technique

Twin-wire plasma arc additive manufacturing of the Ti–45Al titanium aluminide: Processing, microstructures and mechanical properties

Evolution of microstructure and mechanical properties in the molten pool of γ-TiAl alloy synthesized in situ by dual-wire-fed electron beam directed energy deposition.

Effect of Post-Heat Treatment on Ti2AlNb-based Alloy Fabricated by Twin-Wire Alternating Dual-Electron Beam Additive Manufacturing Technology

Wire arc additive manufacturing of the Al-5.55Cu alloy: Insight the effect of intrinsic heat treatment on microstructure and mechanical properties

Fabrication of Titanium Aluminide Alloys by Twin-Wire Tungsten Inert Gas Welding Applied with High-Frequency Induction Heating Wire Technology: Processing, Microstructure, and Properties

Wire Arc Additive Manufacturing of Titanium Aluminide Alloys Using Two-Wire TOP-TIG Welding: Processing, Microstructures, and Mechanical Properties