Abstract:In some traditional formative and additive manufacturing processes widely used in the fabrication of steel products, stress conditions and metallurgy typically result in a strong texture and mechanical anisotropy in both rolling high-strength low-alloy steel and additive manufacturing stainless steel products. To resolve this problem, we have investigated the effectiveness of a novel wire-arc additive manufacturing method in which the heat source is substituted by high-efficiency submerged arc plasma i.e., submerged arc additive manufacturing. An isotropic microstructure can be obtained in the bulk of large-scale low-carbon steel components by ensuring a complete columnar-to-equiaxed transition. We found that the top zone of the as-deposited component comprised columnar α-Fe grains with a typical preferential <001>α orientation. Multiple allotropic transformations were triggered by an in-situ intrinsic heat treatment (mainly the combination of multi-layer-penetration normalizing, full-layer-penetration inter-critical annealing, and long-duration tempering—i.e., NIT). Consequently, when the net bead height was no greater than the width of the fine grain zone affected by the previous layer of deposition, the microstructures in each new layer could be progressively refined and homogenized. Therefore, the intermediate zone was predominantly composed of fully equiaxed α-Fe and displayed homogeneous characteristics along the build direction. During full-layer NIT treatment, the pearlite was spheroidized slightly, reduced both in size (from 4μm to 2μm) and in area fraction (from ~5% to ~1%), thereby mitigating cracking susceptibility. Moreover, not only were the intracrystalline dislocations significantly reduced, but also their morphology evolved from tangled to movable lines. These changes, along with finer grains and the formation of high-angle grain boundaries, led to lower and more dispersed internal strain in the α-Fe matrix. Consequently, excellent Charpy toughness (over 300 J at -60 °C) with minimal deterioration in strength was achieved. Impact, tensile, and hardness tests revealed nearly isotropic mechanical characteristics. We believe that this novel method shows tremendous promise in large-scale additive manufacturing.

In-Situ Regulation to Tailor Additive Manufacturing of TiAl Alloy with Homogeneous Fine Fully Lamellar Colony

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

Additive manufacturing of fine-grain fully lamellar titanium aluminide alloys

In situ design of advanced titanium alloy with concentration modulations by additive manufacturing

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Towards uniform and enhanced tensile ductility of additively manufactured Ti−5Al−5Mo−5V−3Cr alloy through designing gradient interlayer deposition time

A hybrid finite-element and cellular-automaton framework for modeling 3D microstructure of Ti–6Al–4V alloy during solid–solid phase transformation in additive manufacturing

Designing against phase and property heterogeneities in additively manufactured titanium alloys

Clarifying the formation of equiaxed grains and microstructural refinement in the additive manufacturing of Ti-Cu

Novel Strategy for Reducing Residual Stress in Titanium Alloy Parts Obtained via Additive Manufacturing

Promoting the columnar to equiaxed transition and grain refinement of titanium alloys during additive manufacturing

Submerged arc additive manufacturing (SAAM) of low-carbon steel: Effect of in-situ intrinsic heat treatment (IHT) on microstructure and mechanical properties

Nanoscale engineering of low-misfit TiB 2 /Al 3 (Sc,Zr)/α-Al multi-interface to improve strength-ductility synergy for direct energy deposited aluminum alloy

Unravelling heterogeneities in sub-grain cellular structure and micromechanical response of additive manufactured Ti-Nb alloys

Effect of substrate temperature on microstructure and mechanical properties of TiAl alloy fabricated using the twin-wire plasma arc additive manufacturing system

Modification and characterization of the Al concentration induced precipitate in the Fe3Al-based iron aluminide fabricated using the wire-arc additive manufacturing process

Microstructure characteristics of a γ single-phase Ti-55Al-7.5Nb alloy fabricated via additive manufacturing

Implemented in-situ heat treatment process for controlling the residual thermal stresses during the fabrication of Ti-6Al-4V titanium alloy through additive manufacturing

Microstructure and mechanical properties of Al-Cu alloy during wire and arc additive manufacturing by adding micron TiB2 particles

An additively manufactured γ-based high Nb-TiAl composite via coherent interface regulation

Achieving strength-ductility combination and anisotropy elimination in additively manufactured TiB/Ti6Al4V by in-situ synthesized network architecture with fine grains