Abstract:Fiber-optic temperature sensors have gained much attention owing to their intrinsic features of light weight, immunity to electromagnetic interference, and capability for distributed measurement. Especially, temperature sensors based on Fabry-Perot interferometers (FPIs) are attractive owing to their advantages of compact size and convenient reflection measurement. However, due to the low thermal expansion or/and thermo-optic coefficient of fiber, the temperature sensitivities of these sensors are normally low (similar to 10 pm/degrees C or even lower). In order to improve the temperature sensitivity, a device with dual cascaded FPIs is proposed and demonstrated in this paper, which works on vernier effect and exhibits a much higher temperature sensitivity. The device is fabricated by splicing a short segment of large mode area (LMA) fiber to a short segment of capillary tube fused with a section of single-mode fiber to form an extrinsic Fabry-Perot interferometer with a glass cavity cascaded to an intrinsic FPI with a narrow air cavity. By setting the lengths of capillary tube and LMA fiber to allow similar free spectral ranges to be obtained, and superimposing of the reflection spectra of the two FPIs, the vernier effect can be generated. Firstly, the principle of temperature sensing based on vernier effect of this device is analyzed and simulated theoretically, and it is found that the temperature sensitivity can be improved significantly by using vernier effect compared with that of a single FPI with an air-cavity or glass cavity by directly tracing resonant dips/peaks. Then, the temperature responses of the FPI with single air-cavity and dual cascaded cavities are measured, respectively. Experimental results match well with the theoretical analysis carried out. The temperature sensitivity of the proposed sensor is improved greatly from 0.71 pm/degrees C for a single FPI sensor with an air-cavity to 179.30 pm/degrees C by employing the vernier effect. Additionally, the sensor exhibits good repeatability in a temperature range of 100-500. C. The proposed sensor has the advantages of compact size ( < 1 mm in dimension) and high sensitivity, which makes it promising for temperature sensing in a variety of industries, such as food inspection, pharmacy, oil/gas exploration, environment, and high-voltage power systems.

A Highly Sensitive Temperature and Strain Sensor Based on Fiber Lyot Filter with Vernier Effect

Strain Sensor Based on Gourd-Shaped Single-Mode-multimode-single-mode Hybrid Optical Fibre Structure.

Ultrasensitive Temperature and Strain Sensor Based on a Hybrid Fiber Interferometer With the Vernier Effect

Highly Sensitive Strain Sensor Based on the Vernier Effect With High Extinction Ratio and Low-Temperature Cross-Sensitivity by Compact Double FPI

Fiber Optic Temperature Sensor With Online Controllable Sensitivity Based on Vernier Effect

Ultra-high Sensitivity Sensor for Temperature and Strain Measurement Based on Solc-Sagnac Interferometer

High sensitivity fiber optic strain sensor based on CFBG-FPI and vernier effect

Temperature compensation high strain measure ment based on a Fabry-Perot interferometer with the virtual-assisted Vernier effect

Experimental study on a parallel optical fiber Sagnac loops-based sensor with the advantages of both high sensitivity and ultra-wide measurement range

Sensitivity-enhanced temperature sensor with fiber optic Fabry-Perot interferometer based on vernier effect

Temperature self-compensation strain sensor based on cascaded concave-lens-like long-period fiber gratings

Hybrid Interferometer Sensor Based on the Enhanced Vernier Effect for the Simultaneous Measurement of Strain and Temperature

Sensitivity enhanced temperature and strain sensor based on parallel hybrid interferometers and the Vernier effect

Ultrasensitive Temperature Sensor with Vernier-effect Improved Fiber Michelson Interferometer.

High-sensitivity Transverse-Load and High-Temperature Sensor Based on the Cascaded Vernier Effect

Temperature and strain simultaneous sensing measurement based on an all-fiber Mach-Zehnder interferometer and fiber Bragg grating

Simultaneous strain and temperature measurement by cascading few-mode fiber and single-mode fiber long-period fiber gratings

Ultra-sensitive strain sensor composed of tapered two-mode fiber micro-cantilever inserted into quartz capillary

High Sensitivity, Low Temperature-Crosstalk Strain Sensor Based on a Microsphere Embedded Fabry–Perot Interferometer

The Strain Sensor with Enhanced Sensitivity Based on Improved Optical Fiber Michelson Interferometer

Experimental Study of Fiber-Optic Temperature Sensor Based on Dual FSIs