Abstract:This study presents the numerical analysis of single-phase forced convection heat transfer and pressure drop during internal flow in a shallow, rectangular sandwich-like copper channel heated from both the top and the bottom. Simulations were conducted using a commercial finite volume solver that solves governing continuity, momentum, and energy equations simultaneously. The bottom side of the channel was considered with arrays of rectangular miniature-pin fins. The miniature-pin fin geometry was modeled in a staggered configuration with tip clearance from the opposite surface while the orientation of the fins was directed parallel to the flow direction of the working fluid. Water was used as a working fluid with a fully developed velocity profile at the channel entry. Simulations were carried out for varying inlet temperatures and mass flow rates. All calculations were performed with the RNG k-ε model to model complex turbulent flows appropriately. Grid independence and validation analyses were also conducted. With the validated model, additional analyses were performed for 0, 0.1, 0.3, 0.6, and 1 mm tip clearances, and correlations were proposed after performing regression analyses for the friction factor and heat transfer coefficient. The calculations revealed that in contrast to a straight (nonfinned) surface, up to 220% larger heat transfer coefficients could be obtained for the finned surfaces under comparable operating conditions. It was also shown that tip clearance in turbulent flow affects heat transfer negatively. With increasing clearance, the Nusselt number decreased; in other words, heat transfer worsened. On the other hand, the use of miniature-pin fins led to a rise in the pressure drop over the entire heated length. For the Reynolds number spectrum of 4000–20000, the ratio of the friction coefficient of the finned surface to the friction coefficient of the nonfinned surface varied from 6 to 5 while with a further reduction in pressure loss a value of approximately 4 could be obtained for larger tip clearances. Hence, with larger tip clearances, the friction factor decreased, reflecting the abatement of pressure loss.

Numerical study on heat transfer characteristics of a pin–fin staggered manifold microchannel heat sink

Study on the flow and heat transfer characteristics of pin-fin manifold microchannel heat sink

An Experimental Study of Microchannel and Micro-Pin-Fin Based On-Chip Cooling Systems with Silicon-to-Silicon Direct Bonding.

Experimental study of embedded manifold staggered pin-fin microchannel heat sink

Thermohydraulic Performance Optimization of Integrated Porous Pin Fins in Microchannel Heat Sink Using Shape Optimization Coupled with NSGA

Fluid Flow and Heat Transfer Performance in a Micro-Reactor with Non-Uniform Micro-Pin-fin Arrays for Hydrogen Production at Low Reynolds Number

Experimental and numerical investigation on turbulent convection enhancement in minichannel heat sink with staggered V-shaped pin fins

Heat Transfer Enhancement of Microchannel Heat Sink Using Sine Curve Fins

Single-phase and Two-phase Flow and Heat Transfer in Microchannel Heat Sink with Various Manifold Arrangements

Effect of fin shapes on flow boiling heat transfer with staggered fin arrays in a heat sink

A Numerical Study of Subcooled Flow Boiling in a Manifold Microchannel Heat Sink with Varying Inlet-to-outlet Width Ratio

Numerical Study on Hybrid Discontinuous Microchannel Heat Sink Combining Manifold with Pin Fins (DMC-MPF) for High Power Electronic Device

Investigation of flow and heat transfer performance of the manifold microchannel with different manifold arrangements

Numerical study on hydrothermal performance in a microchannel with gradient array of ribs and pin fins

Numerical Study on Flow and Heat Transfer of a Hybrid Microchannel Cooling Scheme Using Manifold Arrangement and Secondary Channels

A Comparative Numerical Study on Two-Phase Boiling Fluid Flow and Heat Transfer in the Microchannel Heat Sink with Different Manifold Arrangements

Numerical Investigation Of Flow Boiling In A Manifold Microchannel Heat Sink With Conjugate Heat Transfer

Micro Pin Fins with Topologically Optimized Configurations Enhance Flow Boiling Heat Transfer in Manifold Microchannel Heat Sinks

Heat Transfer and Flow Characteristics of Flow Boiling in Manifold Microchannel

Investigation of heat transfer performance of the manifold microchannel heat sink with different interface configurations

Numerical study of the intensification of single-phase heat transfer in a sandwich-like channel using staggered miniature-pin fins