Abstract:A microchannel heat sink (MCHS) is known as a heat dissipation device from the miniaturized electronic components and devices due to its capability to dissipate high heat flux from smaller surface area. However, the higher pressure drop and the uneven heat removal along the channel length are the noticeable disadvantages of MCHS. Though there are attempts to address these shortcomings, no existing study has been found to study the effect of positions of microstructures (micro-pin fin and blind holes) and combined effect of micro-pin fins and blind holes under flow boiling condition. Therefore, in the present study, an attempt has been made to logically explain the effect of various arrangements and positions of pin fins and blind holes in the selected twenty-four uniformly distributed stations on the thermohydraulic performance of MCHS through numerically predicted results. The objectives of the study have been attained using the following three analyses, flow boiling, (i) with saturated fluid inlet conditions (inlet Re = 500), (ii) with different inlet subcooling (20, 40, and 60 °C ), and (iii) with different heat flux conditions (100, 150, 200 and 250 W/cm2 ). From the study, it is observed that the pin fin enhances heat transfer in single-phase flow and delays the phase change by disturbing the flow. The blind holes act as nucleation sites and help phase change heat transfer. It is also observed that the ratio of single-phase and two-phase length and arrangement of microstructures in these two regions predominately dominate the heat transfer and fluid flow characteristics of the microchannel heat sink. The optimum performance (maximum heat transfer coefficient and minimum pressure drop) is achieved when twelve pin fins are placed in the upstream half and twelve blind holes are located at the downstream half of the channel. However, design improvement is possible through more computational and experimental analysis.

Numerical study on hydrothermal performance in a microchannel with gradient array of ribs and pin fins

Thermohydraulic Performance Optimization of Integrated Porous Pin Fins in Microchannel Heat Sink Using Shape Optimization Coupled with NSGA

An Experimental Study of Microchannel and Micro-Pin-Fin Based On-Chip Cooling Systems with Silicon-to-Silicon Direct Bonding.

Fluid Flow and Heat Transfer Performance in a Micro-Reactor with Non-Uniform Micro-Pin-fin Arrays for Hydrogen Production at Low Reynolds Number

Numerical Study on Performances of Mini-Channel Heat Sinks with Non-Uniform Inlets

Numerical analysis on thermal-hydraulic performance of optimized microchannel heat sink with slant ribs and quatrefoil rib-elliptical groove complex structures

Numerical Investigations of the Thermal-Hydraulic Characteristics of Microchannel Heat Sinks Inspired by Leaf Veins

Numerical simulation study of thermal and hydraulic characteristics of laminar flow in microchannel heat sink with water droplet cavities and different rib columns

Numerical Study on Heat Transfer Efficiency and Inter-Layer Stress of Microchannel Heat Sinks with Different Geometries

Numerical study of different micro-channel structures on fluid flow and heat transfer performance

Numerical investigation on thermal-hydraulic characteristics of the micro heat sink with gradient distribution pin fin arrays and narrow slots

Study on the efficient heat transfer mechanism of microchannel pin-fin arrays under low pumping power

Experimental and Numerical Study of a Trapezoidal Rib and Fan Groove Microchannel Heat Sink

Numerical simulation of fluid and heat transfer characteristics of microchannel heat sink with fan-shaped grooves and triangular truncated ribs

Development and numerical investigation of novel gradient-porous heat sinks

Computational analysis of microchannel heat sinks with constant circular pin fins: Performance evaluation and optimization

Numerical Study on Hybrid Discontinuous Microchannel Heat Sink Combining Manifold with Pin Fins (DMC-MPF) for High Power Electronic Device

Thermal Performance of a Double Layer Microchannel Heat Sink with Staggered Triangular Ribs in the Transverse Microchambers

Fluid flow and heat transfer characteristics of a microstructured microchannel heat sink under flow boiling condition

Numerical investigations of heat transfer augmentation in a microchannel heat sink with different shaped periodic reentrant cavities on channel sidewalls

Experimental and numerical investigation on the heat transfer enhancement for Mini-channel heat sinks with tessellated fins