Abstract:Li 7 La 3 Zr 2 O 12 (LLZO) garnet-type lithium-ion conductors are being investigated as a promising solid electrolyte for solid-state lithium batteries. To enable a functional all-solid-state configuration intensive investigations are needed to reduce the cathode/electrolyte interfacial resistance which contributes the most to cell performance loss. Among the commercial cathode materials investigated so far, LiCoO 2 (LCO) is one of the most stable with garnet electrolytes as only a superficial reaction has been detected between the two materials. However, even this minor reaction would block the Li-ion transport through the interface, resulting in deteriorated cell performance. In this work, we demonstrate that a thin aluminum oxide layer (5 nm) can be an effective interlayer to impede the formation of a harmful interphase and enable facile Li-ion transfer between LCO and the LLZO garnet. Room-temperature-sputtered LCO thin films were employed to form an interface with the garnet electrolyte and annealed at 800 °C to reveal the effect of the interfacial reaction on the Li-ion transfer across the interface. An aluminum oxide layer was then introduced between LCO and the garnet electrolyte by sputtering a metallic aluminum layer which is then annealed together with the upper LCO layer in oxygen, or by direct atomic layer deposition of the oxide. Compared to the LCO/LLZO/Li cells without an aluminum oxide interlayer, those with the interlayer exhibited improved performance, i.e., a stable discharge capacity of up to 90 mAh/(g LCO) at a C/10 rate, a rate capability up to 1.68C and a stable galvanostatic cycling at 0.1C for over 100 cycles with a discharge capacity fade rate of 0.15% per cycle. It was determined that aluminum diffused into the LCO layer after preventing the initial detrimental reaction between LCO and the LLZO garnet from happening during high temperature annealing, suggesting that the coating does not have to remain a physically blocking layer during cycling to function.

A Simple and Efficient Strategy for Ameliorating Li/LLZO Interfacial Contact

In Situ Formed Surface Layer to Improve the Air Stability of LLZTO and Its Contact with the Li Metal

Achieving Efficient and Stable Interface Between Metallic Lithium and Garnet-Type Solid Electrolyte Through a Thin Indium Tin Oxide Interlayer

Interface Engineering for Garnet-Type Electrolyte Enables Low Interfacial Resistance in Solid-State Lithium Batteries

Well-contacted Li/LLZTO interface by citric acid aqueous treatment for solid-state Li metal batteries

All Solid-State Li/LLZO/LCO Battery Enabled by Alumina Interfacial Coating

One-Step Processing of Soft Electrolyte/Metallic Lithium Interface for High-Performance Solid-State Lithium Batteries

Improving the Interfacial Contact between Li 7 La 3 Zr 2 O 12 and Lithium Anode by Depositing a Film of Silver

In-situ construction of Li-Mg/LiF conductive layer to achieve an intimate lithium-garnet interface for all-solid-state Li metal battery

Growth Process and Removal of Interface Contaminants for Garnet-Based Solid-State Lithium Metal Batteries

The Interface Between Li6.5La3Zr1.5Ta0.5O12 and Liquid Electrolyte

In-situ constructed lithium-salt lithiophilic layer inducing bi-functional interphase for stable LLZO/Li interface

Reducing Impedance at a Li-Metal Anode/Garnet-Type Electrolyte Interface Implementing Chemically Resolvable In Layers

Constructing a Li2O/LiZn Mixed Ionic Electron Conductive Layer by Ultrasonic Spraying to Enhance Li/Garnet Solid Electrolyte Interface Stability for Solid-State Batteries.

osure and surface chemistry on Li – Li 7 La 3 Zr 2 O 12 interfacial resistance †

Impact of Air Exposure and Surface Chemistry on Li-Li7la3zr2o12 Interfacial Resistance

Interfacial Stability of Li Metal-Solid Electrolyte Elucidated Via in Situ Electron Microscopy.

In‐Situ Construction of Electronically Insulating and Air‐Stable Ionic Conductor Layer on Electrolyte Surface and Grain Boundary to Enable High‐Performance Garnet‐Type Solid‐State Batteries

Co-doping strategy enhanced the ionic conductivity and excellent lithium stability of garnet-type Li7La3Zr2O12 electrolyte in all solid-state lithium batteries

Improving Li/garnet Interface by Amorphous SnO2 Interlayerdeposited Via Sol–gel Method

3D lithiophilic framework fixed on the surface of LLZTO solid electrolyte shaping the contact between Li metal and ceramic