Abstract:Continuous fiber-reinforced ceramic matrix composites are promising materials for advanced hot end components and safety-critical components of aeronautics and astronautics; however, the difficult-to-process problem of these materials has been one of the technical bottlenecks restricting their high-performance service. The present work proposed a novel high-efficiency, low-damage, and low-abrasive wear processing method based on the chemical properties of the materials, which used lasers to ablate workpieces before grinding—laser-induced ablation-assisted grinding (LIAAG). The material removal mechanism of Cf/SiC composites was investigated by single-grain scratching tests; the grinding performances of LIAAG in terms of grinding force, grinding temperature, surface integrity, abrasive wear, grinding chips were evaluated by a contrast abrasive belt grinding test. It was found that Cf/SiC composites were chemically transformed into relatively loose and homogeneous ablation products (SiO2 and recrystallized SiC) at high laser ablation temperatures, which were easier to remove during grinding. In this case, surface morphologies displayed the microfracture and crushing of carbon fibers and SiC matrixes, and the grinding-induced damages, such as macro fracture, fiber pull-out, interface debonding, were significantly contained. Abrasive belt was primarily worn in micro-adhesion and micro-abrasion, rather than cleavage fracture and the fall-off in traditional grinding. Under optimum parameters, the grinding force, grinding temperature, and average surface roughness of belt grinding were reduced by 47 %, 40 %, and 26 %, respectively. Consequently, the surface integrity was improved greatly, and the abrasive wear was reduced significantly. The work provides a vital high-performance processing method for ceramic matrix composites components.

Enhancing Ductile Removal of Cf/SiC Composites During Abrasive Belt Grinding Using Low-Hardness Rubber Contact Wheels

Material removal behavior of C<sub>f</sub>/SiC ceramic matrix composites as a function of abrasive wear during diamond abrasive belt grinding

A novel low-damage and low-abrasive wear processing method of Cf/SiC ceramic matrix composites: Laser-induced ablation-assisted grinding

Wear-induced variation of surface roughness in grinding 2.5D C f /SiC composites

Study of Material Removal Mechanisms in Grinding of C/SiC Composites Via Single-Abrasive Scratch Tests

Wear-induced Variation of Surface Roughness in Grinding 2.5D Cf/SiC Composites

Investigation on the machined surface quality and removal mechanism of SiCf/SiC composites in ultrasonic-assisted grinding

Experimental Investigation on Tool Wear in Ultrasonic Vibration-Assisted Turning of SiCf/SiC Ceramic Matrix Composite

Significant improvement of machinability of C f /SiC composites through matching laser scanning spacing and abrasive belt grain size

Study on Removal Mechanism and Surface Quality of SiCf/SiC Composites by Longitudinal Torsional Ultrasonic Vibration-Assisted Grinding

Influence Factors on Grinding Force in Surface Grinding of Unidirectional C/SiC Composites

Grinding characteristics and removal mechanisms of unidirectional carbon fibre reinforced silicon carbide ceramic matrix composites

Understanding of the effect of wear particles removal from the surface on grinding silicon carbide by molecular dynamics simulations

Significant Improvement of Machinability of Cf/SiC Composites Through Matching Laser Scanning Spacing and Abrasive Belt Grain Size

Comprehensive Investigation into Grinding Characteristics and Damage Behavior of Cf/SiC Composite Modified by Picosecond-Laser Ablating

Scratch-induced Surface Formation Mechanism in C/SiC Composites

Understanding Machinability Improvements and Removal Mechanism of Ceramic Matrix Composites During Laser-Ablating Assisted Grinding

Single diamond scribing of SiCf/SiC composite: Force and material removal mechanism study

Influence of the fiber orientation on 3D C/C–SiC composite material and its formation mechanism of the machining surface

Grinding Characteristics and Removal Mechanism of 2.5D-Needled Cf/SiC Composites

Subsurface Damage Inhibiting and Synchronous Removal Behavior of Cf/SiC Composites with Laser-Induced Controllable Ablation During Abrasive Belt Grinding