Abstract:The electron transport layer is an important functional layer of perovskite solar cells, and its surface and internal defects are critical parts of limiting the performance improvement of perovskite solar cells. The double electron transport layer (double ETL) strategy enables effective passivation of the inherent defects in the electron transport layer (e.g., SnO2) and improves the extraction and transport of electrons between the functional layers, which provides an effective way for the development of high-efficiency and stable PSCs. However, due to the existence of independent interfaces within the dual ETL, the issue of cell mismatch of different ETL materials also leads to additional carrier defects, impeding the ongoing advancement of the dual ETL strategy.This work proposes a strategy to introduce di[2-((oxo) diphenylphosphino) phenyl]ether (DPEPO) into SnO2 ETL to design a hybrid electron transport layer strategy. Taking advantage of DPEPO's hole-blocking effect with higher HOMO energy levels and good electron transport ability, it successfully passivates the intrinsic defects in SnO2, while significantly improving the crystalline quality of the surface of the SnO2 film. So, avoiding the direct contact between the perovskite photoactive layer and the conductive substrate, which effectively improves the extraction and transport of electrons. Due to the preparation of high-quality electron transport layer, the crystalline regulation of perovskite thin film was further achieved to enhance the performance of perovskite solar cells, which finally harvested a power conversion rate of 21.53%, in which the open-circuit voltage (VOC) reached 1.220 V, the short-circuit current (JSC) was 23.19 mA/cm2, and the fill factor (FF) was 76.11%. This efficiency is 1.39% higher than that of the control one. It is shown that the hybrid electron transport layer strategy can not only optimize the carrier transport dynamics efficiently and significantly reduce the device performance affected by the defects in the functional layer, but also regulate the perovskite crystallization, which is promising for the preparation of high-performance solar cells.

Defect Management by a Cesium Fluoride-Modified Electron Transport Layer Promotes Perovskite Solar Cells.

Enhancing Electron Extraction and Transport in Inorganic Perovskite Solar Cells Via Additional Built-in Potential of SnO2-BiFeO3 Nano-Heterostructure

Managing Interfacial Defects and Charge-Carriers Dynamics by a Cesium-Doped SnO2 for Air Stable Perovskite Solar Cells

Superior SnO2 Electron Transport Layer Via Bifunctional Interfacial Regulation Using Cesium Sulfate for Efficient Perovskite Solar Cell

Enhanced Efficiency and Stability of Planar Perovskite Solar Cells Using SnO2:InCl3 Electron Transport Layer Through Synergetic Doping and Passivation Approaches

Enhanced Charge Transport and Interface Passivation in Efficient Perovskite Solar Cells Using Sulfur‐Doped Graphite Carbon Nitride‐Modified SnO2‐Based Electron Transport Layers

Simultaneous Passivation of the SnO2/Perovskite Interface and Perovskite Absorber Layer in Perovskite Solar Cells Using KF Surface Treatment

Enhanced Charge Transport and Interface Passivation in Efficient Perovskite Solar Cells Using Sulfur‐Doped Graphite Carbon Nitride‐Modified SnO 2 ‐Based Electron Transport Layers

Enhancing the Efficiency of Perovskite Solar Cells by Bidirectional Modification of the Perovskite and Electron Transport Layer

Reduced Surface Hydroxyl and Released Interfacial Strain by Inserting CsF Anchor Interlayer for High‐Performance Perovskite Solar Cells

Thiazole‐Modified C3N4 Interfacial Layer for Defect Passivation and Charge Transport Promotion in Perovskite Solar Cells

Multifunctional Interface Treatment of Phosphate for High-Efficiency Perovskite Solar Cells

Performance of Perovskite Solar Cells Based on SnO<sub>2</sub>: DPEPO Hybrid Electron Transport Layer

CuCl2-modified SnO2 electron transport layer for high efficiency perovskite solar cells

Interfacial Energy Level Alignment and Defect Passivation by Using a Multifunctional Molecular for Efficient and Stable Perovskite Solar Cells

Thiazole‐Modified C 3 N 4 Interfacial Layer for Defect Passivation and Charge Transport Promotion in Perovskite Solar Cells

Facile Surface Engineering of Composite Electron Transport Layer for Highly Efficient Perovskite Solar Cells with a Fill Factor Exceeding 81%

CuCl2-modified SnO2electron Transport Layer for High Efficiency Perovskite Solar Cells.

High-effective SnO2-based perovskite solar cells by multifunctional molecular additive engineering

Vertical Phase Separated Cesium Fluoride Doping Organic Electron Transport Layer: A Facile and Efficient “bridge” Linked Heterojunction for Perovskite Solar Cells

CsI Enhanced Buried Interface for Efficient and UV‐Robust Perovskite Solar Cells