Abstract:In this study, the process of carbon dioxide (CO2) capture directly from ambient air in a conventional monoethanolamine (MEA) absorption process was simulated and optimized using a rate-based model in Aspen Plus. The process aimed to capture a specific amount (148.25 Nm3/h) of CO2 from the air, which was determined by a potential application aiming to produce synthetic methane from the output of a 2.7 MW electrolyser (593 Nm3/h H2). We investigated the technical performance of the process by conducting a sensitivity analysis around different parameters such as air humidity, capture rate defined as a ratio of moles of CO2 captured during the process to the total mole of CO2 in the feed stream, CO2 loading of lean and rich absorption liquids and reboiler temperature, and evaluated the energy consumption and overall cost in this system. In order to meet the design requirement for standard packed columns, the rich absorption liquid was circulated to the top of the absorber. A capture rate of 50% was selected in this process as a baseline. At higher capture rates, the required energy per ton of captured CO2 increases due to a higher steam stripping rate, required in the desorber, and at lower capture rates, the size of equipment, in particular, absorber and blowers increases due to the need for processing a significantly larger volume of air at the given CO2 production volume. At the base case scenario, a reboiler duty of 10.7 GJ/tCO2 and an electrical energy requirement of 1.4 MWh/tCO2 were obtained. The absorber diameter and height obtained were 10.4 and 4.4 m, respectively. The desorber is found to be relatively small at 0.54 m in diameter and 3.0 m in height. A wash water section installed at top of the absorber decreased the MEA loss to 0.28 kg/ton CO2. However, this increased capital cost by around 60% resulting in CO2 capture costs of $1,691 per ton CO2 for the MEA base scenario. Based on the techno-economic analysis, assuming a non-volatile absorbent rather than MEA thereby avoiding a wash water section, and using an absorption column built from cheaper materials, the estimated cost per ton of CO2 produced was reduced to $676/tCO2. The overall cost range was between $273 and $1,227 per ton of CO2 depending on different economic parameters such as electricity ($20–$200/MWh) and heat price ($2–$20/GJ), plant life (15–25 years) and capital expenditure (±30%). In order to reduce the cost further, the use of innovative cheap gas-liquid contactors that operate at lower liquid to gas ratios is crucial.

Techno-economic Evaluation of Post-Combustion Carbon Capture Based on Chemical Absorption for the Thermal Cracking Furnace in Ethylene Manufacturing

Optimization of Post Combustion CO2 Capture from a Combined-Cycle Gas Turbine Power Plant via Taguchi Design of Experiment

Techno-Economic Assessment for CO2 Capture From Air Using a Conventional Liquid-Based Absorption Process

Development and testing of a new post-combustion CO2 capture solvent in pilot and demonstration plant

Heat Integration, Process Design and Techno-Economic Assessment of Post-Combustion Carbon Capture Using Piperazine for Large-Scale Ethylene Plant

Energy, exergy, environmental and economic analysis of solvent-based post-combustion carbon capture for ethylene production

Energy-efficient Process Intensification for Post-Combustion CO2 Capture: A Modeling Approach

CO2 Utilization Via Integration of an Industrial Post-Combustion Capture Process with a Urea Plant: Process Modelling and Sensitivity Analysis

Industrial test of post combustion CO2 capture by reactive absorption with two new solvents in natural gas power plant

Techno-Economic Assessment of Amine-Based Carbon Capture in Waste-to-Energy Incineration Plant Retrofit

Study on the Integration of Fluid Catalytic Cracking Unit in Refinery with Solvent-Based Carbon Capture Through Process Simulation

Improved CO2 Capture Method by Absorption

Integration of membrane contactors and catalytic solvent regeneration for efficient carbon dioxide capture

Comparative Techno-Economic Analysis of CO2 Capture Processes Using Blended Amines

Economic Analysis of CO2 Separation from Coal-Fired Flue Gas by Chemical Absorption and Membrane Absorption Technologies in China

MEA-based CO2 capture: a study focuses on MEA concentrations and process parameters

Rate-Based Modelling and Validation of an Absorber and Stripper in an Amine-Based Post-Combustion CO2 Capture Process

Simulation Optimization of A New Ammonia-Based Carbon Capture Process Coupled with Low-Temperature Waste Heat Utilization

Ionic Liquid-Ethanol Mixed Solvent Design for the Post-Combustion Carbon Capture

An integrated de-carbonization supercritical coal-fired power plant incorporating a supplementary steam turbine, process heat recovery and a modified boiler structure

Comparative Investigation of Different CO2 Capture Technologies for Coal to Ethylene Glycol Process