Abstract:The oxide dispersion strengthened Mo alloys (ODS-Mo) prepared by traditional ball milling and subsequent sintering technique generally possess comparatively coarse Mo grains and large oxide particles at Mo grain boundaries (GBs), which obviously suppress the corresponding strengthening effect of oxide addition. In this work, the Y 2 O 3 and TiC particles were simultaneously doped into Mo alloys using ball-milling and subsequent low temperature sintering. Accompanied by TiC addition, the Mo−Y 2 O 3 grains are sharply refined from 3.12 to 1.36 μm. In particular, Y 2 O 3 and TiC can form smaller Y−Ti−O−C quaternary phase particles (∼230 nm) at Mo GBs compared to single Y 2 O 3 particles (∼120 nm), so as to these new formed Y−Ti−O−C particles can more effectively pin and hinder GBs movement. In addition to Y−Ti−O−C particles at GBs, Y 2 O 3 , TiO x , and TiC x nanoparticles (<100 nm) also exist within Mo grains, which is significantly different from traditional ODS-Mo. The appearance of TiO x phase indicates that some active Ti within TiC can adsorb oxygen impurities of Mo matrix to form a new strengthening phase, thus strengthening and purifying Mo matrix. Furthermore, the pure Mo, Mo−Y 2 O 3 , and Mo−Y 2 O 3 −TiC alloys have similar relative densities (97.4%–98.0%). More importantly, the Mo−Y 2 O 3 −TiC alloys exhibit higher hardness (HV 0.2 (425 ± 25)) compared to Mo−Y 2 O 3 alloys (HV 0.2 (370 ± 25)). This work could provide a relevant strategy for the preparation of ultrafine Mo alloys by facile ball-milling.

Effect of Different Y Components on Optimization of Dispersive Y2O3 Particles in ODS-Cu

The optimization of Cu6Y sourced ODS-Cu: Effect of Y2O3 content

Effect of Y Precursors on the Synthesis of Cu-Y2o3 by Mechanical Alloying and Spark Plasma Sintering

Microstructure development of Y–Ti–O dispersion strengthened Cu alloys fabricated by mechanical alloying

Development of Y2O3 Dispersion-Strengthened Copper Alloy by Sol-Gel Method

Effects of composite oxide addition on the microstructure and properties of ODS copper

Effect of process control agent on the synthesis of Cu-Y2O3 by mechanical alloying

Study of Cu Effect and In-situ Yttria Dispersoids on Microstructure Evolution of Mechanically Alloyed CoFeNiCrCu High Entropy Alloys

Microstructure and properties of Y2O3/Cu composites fabricated by a novel liquid phase in situ reactive synthesis process

Effect of Y2O3 Addition on the Microstructure, Wear Resistance, and Corrosion Behavior of W-4.9Ni-2.1Fe Heavy Alloy

Effect of Y/Ti Atomic Ratio on Microstructure of Oxide Dispersion Strengthened Alloys

Achieving ultrahigh strength in oxide-dispersion-strengthened CoCrNi alloy via in situ formation of coherent Y-Ti-O nanoprecipitates

Microstructure refinement and second phase particle regulation of Mo−Y2O3 alloys by minor TiC additive

Multiphase strengthening mechanism of Cu-Y2O3/W composites prepared by mechanical alloying

Effect of nano-Y2O3 on the microstructure and mechanical properties of Cu-10W composites prepared by spark plasma sintering

Preparation of nanostructural oxide dispersion strengthened (ODS) Mo alloy by mechanical alloying and spark plasma sintering, and its characterization

Effect of Y2O3 on High Temperature Thermal Compression Performance of Cu-10W Composites and Microstructure Analysis

Microstructure, Mechanical Properties, and Strengthening Mechanisms of Nanostructural Y-Zr-O Oxide Dispersion-Strengthened (ODS) Mo Alloys

Effect of Y2O3 and TiO2 addition of dispersed powder on phase evolution and microstructural analysis of (Al, Cu)3Ti intermetallic synthesised via mechanical alloying and powder metallurgy route

Effect of oxide nanoparticles on the mechanical properties of novel cobalt-free FeCrNi medium entropy alloys

Effect of Y on microstructure, damping properties and mechanical properties of Cu-Al-Ni-Mn alloy