Abstract:4D printing allows 3D printed structures to change their shapes overtime under external stimuli, finding a wide range of potential applications in actuators, soft robotics, active metamaterials, flexible electronics, and biomedical devices. However, most 4D printing uses soft polymers to accommodate large strain shape-changing capability at the price of low stiffness, which impedes their engineering applications. Here, we demonstrate an approach to design and manufacture self-morphing structures with large deformation and high modulus (∼4.8 GPa). The structures are printed by multimaterial direct ink writing (DIW) using composite inks that contain a high volume fraction of solvent, photocurable polymer resin, and short glass fibers as well as fumed silica. During printing, the glass fibers undergo shear-induced alignment through the nozzle, leading to highly anisotropic mechanical properties. The solvent is then evaporated, during which the aligned glass fibers enable anisotropic shrinkage in the parallel and perpendicular directions to the fiber alignment for shape shifting. A final postphotocuring step is applied to further increase the stiffness of the composite from ∼300 MPa to ∼4.8 GPa. A finite element analysis (FEA) model is developed to predict the influence of the solvent, fiber contents, and fiber orientation on the shape shifting. We demonstrate the anisotropic volume shrinkage of the structures can be used as active hinges to transform printed two-dimensional structures into complex three-dimensional structures with large shape-shifting and outstanding mechanical properties. This strategy for fabricating composite structures with programmable architectures and excellent mechanical properties shows potential applications in morphing lightweight structures with load-bearing capabilities.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c18988?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c18988</a>.Model of anisotropic mechanical properties during volume shrinking for partially cured short glass fiber reinforced composites (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c18988/suppl_file/am0c18988_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

4D Printing of Shape-Changing Structures Based on IPN Epoxy Composites Formed by UV Post-Curing and Γ-Ray Radiation

Modular 4D Printing Via Interfacial Welding of Digital Light-Controllable Dynamic Covalent Polymer Networks

Photosensitive Composite Inks for Digital Light Processing Four-Dimensional Printing of Shape Memory Capture Devices

Design of enhanced mechanical properties by interpenetrating network of 3D printing dual-curing resins

Fabrication of tough epoxy with shape memory effects by UV-assisted direct-ink write printing

Modeling the Printability of Photocuring and Strength Adjustable Hydrogel Bioink During Projection-Based 3D Bioprinting.

High-Speed 3D Printing of High-Performance Thermosetting Polymers via Two-Stage Curing

Reconfigurable Polymer Networks for Digital Light Processing 3D Printing

4D Printing Of Shape Memory Epoxy For Adaptive Dynamic Components

Top-down digital light processing 3D printing of composite structures using carbon fiber modified UV curable resin

Multiphoton Lithography of Interpenetrating Polymer Networks for Tailored Microstructure Thermal and Micromechanical Properties

Digital light processing 4D printing multilayer polymers with tunable mechanical properties and shape memory behavior

Three-Dimensional Printing of Shape Memory Composites with Epoxy-Acrylate Hybrid Photopolymer.

Unstructured Direct Ink Write 3D Printing of Functional Structures with Ambient Temperature Curing Dual‐Network Thermoset Ink

Regulation of the Interface Compatibility of the 3D-Printing Interpenetration Networks Toward Reduced Structure Anisotropy and Enhanced Performances

Simultaneous One-Pot Interpenetrating Network Formation to Expand 3D Processing Capabilities

4D Printing of Glass Fiber-Regulated Shape Shifting Structures with High Stiffness

Study on Chemical Graft Structure Modification and Mechanical Properties of Photocured Polyimide

4D Printing of Shape Memory Polyurethane Via Stereolithography

Cross-linking degree modulation of 4D printed continuous fiber reinforced thermosetting shape memory polymer composites with superior load bearing and shape memory effects

DLP 3D Printing of High-Performance Epoxy Resin Via Dual Curing