Abstract:Lithium metal anode is recognized as the "Holy Grail" electrode because of its high specific capacity (3860 mAh/g) and low reduction potential (-3.04 V vs. standard hydrogen electrode), which is meaningful for batteries systems. Remarkable improvement of ionic conductivity of sulfide electrolyte exceeding 10 mS/cm at room temperature has opened up the opportunity to realized the commercialization of lithium metal anode. However, the practical implement of Li anode in solid-state batteries is hundered by the poor cycle stability and the low energy efficiency stemming from the unstable interfaces due to the ultrahigh reactivity of lithium metal. At the anode interface, the lithium dendrite growth and solid electrolytes (SE) reduction by lithium metal are serious challenges for lithium metal anode. To suppress the interfacial reactions and lithium dendrite formation at the sulfide electrolyte/Li metal anode interface, various strategies have been implemented by researchers, such as in situ formed robust SEI (solid electrolyte interface), surface modification and SE modification, etc. In this article, we focus on the artificial solid electrolyte interface (ASEI) to strengthening the Li metal and solid electrolyte interface. We fabricate the uniform LiF-rich ASEI using CF3(CF2)(3)OCH3 by heating at a temperature of 150 degrees C for 6 h. LiF layer at the interface between Li and sulfide electroyte could prevent Li dendrite growth. Compared to the Li/sulfide electrolyte interface, the Li/LiF/sulfide electrolyte interface is more stable. The symmetrical cell LiF@Li//Li6PS5Cl//LiF@Li (LiF@Li//LPSCl//LiF@Li) does not short-circuit after 40 cycles at the current density of 0.1 mAh/cm(2) with a lower polarization potential. A solid-state battery LiNbO2@LiCoO2//LPSCl//LiF@Li (LNO@LCO//LPSCl//LiF@Li) employing LiF coated Li metal as anode shows a high reversible discharge capacity of 138.4 mAh/g at 0.05 C and retains 110.9 mAh/g after 50 cycles. This interficial engineering for lithium metal and sulfide solid electrolyte provides new opportunity to commercialize the Li metal batteries.

Realizing the Compatibility of a Li Metal Anode in an All-Solid-state Li−S Battery by Chemical Iodine–vapor Deposition

Realizing compatibility of Li metal anode in all-solid-state Li-S battery by chemical iodine–vapor deposition

A Bifunctional Composite Artificial Solid Electrolyte Interphase for High Stable Solid-State Lithium Batteries

A Dynamically Stable Sulfide Electrolyte Architecture for High-Performance All-Solid-State Lithium Metal Batteries

Li metal coated with Li3PO4 film via atomic layer deposition as battery anode

An artificial layer enables in situ generation of a homogeneous inorganic/organic composite solid electrolyte interphase for stable lithium metal batteries

In Situ Formed LiI Interfacial Layer for All-Solid-State Lithium Batteries with Li6PS5Cl Solid Electrolyte Membranes.

Achieving multi-dimensional Li + transport nanochannels via spatial-partitioning in crystalline ionic covalent organic frameworks for highly stable lithium metal anode

Interficial Engineering of Lithium Metal Anode for Sulfide Solid State Batteries

An in Situ-Formed LiI Interface Layer for Garnet-Based Lithium Metal Batteries

Toward Ultrastable Metal Anode/Li 6 PS 5 Cl Interface via an Interlayer as Li Reservoir

Integrated Interface Configuration by In-Situ Interface Chemistry Enabling Uniform Lithium Deposition in All-Solid-state Lithium Metal Batteries

Multifunctional and Seamlessly Integrated Soft/Rigid Interphase Realizing a Stable Lithium-Metal Anode for a High-Performance Lithium-Metal Battery under a Lean Electrolyte

In-situ formed decrystallized interphase enabled high performance all-in-one all-solid-state batteries

In Situ Ion‐Conducting Protective Layer Strategy to Stable Lithium Metal Anode for All‐Solid‐State Sulfide‐Based Lithium Metal Batteries

Domain-Limited Laminar Lithium Deposition Behavior Mediated by the Design of Hybrid Anode for Sulfide-Based All-Solid-State Batteries

Realizing the Dendrite-Free Sulfide-Based All-Solid-state Li Metal Battery by Surface Design

In Situ construction of PVDF/LLTO electrolyte with stable electrolyte/electrode interphase for integrated solid-state lithium batteries

A Li3Bi/LiF interfacial layer enabling highly stable lithium metal anode

Uniform High Ionic Conducting Lithium Sulfide Protection Layer for Stable Lithium Metal Anode

In Situ Solid Electrolyte Interphase from Spray Quenching on Molten Li: A New Way to Construct High-Performance Lithium-Metal Anodes.