Abstract:All-solid-state lithium-metal batteries (ASSLBs) have attracted intense interest due to their high energy density and high safety. However, Li dendrite growth and high interface resistance remain challenging due to insufficient understanding of the mechanism. Here we develop two types of porous lithiophobic interlayer (Li 7 N 2 I–carbon nanotube and Li 7 N 2 I–Mg) to enable Li to plate at the Li/interlayer interface and reversibly penetrate into the porous interlayer. The experimental and simulation results reveal that a balance of lithiophobicity, electronic and ionic conductivities and interlayer's porosity are the key enablers for stable Li plating/stripping at a high capacity. A fine-tuned Li 7 N 2 I–carbon nanotube interlayer enables Li/LNI/Li symmetric cell to achieve a high critical current density of 4.0 mA cm −2 at 4.0 mAh cm −2 at 25 °C; the Li 7 N 2 I–Mg interlayer enables a Li 4 SiO 4 @LiNi 0.8 Mn 0.1 Co 0.1 O 2 /Li 6 PS 5 Cl/20 μm-Li full cell to achieve an areal capacity of 2.2 mAh cm −2 , maintaining 82.4% capacity retention after 350 cycles at 60 °C at a rate of 0.5 C. The interlayer design principle opens opportunities to develop safe and high energy ASSLBs.

What problem does this paper attempt to address?

The paper primarily focuses on the issue of lithium anode interface design in all-solid-state lithium-metal batteries. Specifically, the research team developed a solid electrolyte based on lithium nitride (LNI) and explored how to improve the performance of lithium-metal batteries by designing an appropriate interlayer. The main objectives of the study are as follows: 1. **Develop LNI solid electrolyte**: The researchers prepared a yellow LNI solid electrolyte with high ionic conductivity (3.1×10^-4 S cm^-1) and low lithium migration activation energy (0.34 eV), which is stable against lithium metal at room temperature. 2. **Address the lithium dendrite growth issue**: Due to the high lithiophobicity of LNI, it can inhibit the outward growth of lithium dendrites. However, this high lithiophobicity also leads to void formation, which increases the overpotential for lithium deposition/stripping and promotes lithium dendrite growth. 3. **Design a carbon-LNI composite interlayer**: To overcome the above issues, the researchers designed a porous carbon-LNI composite material as an interlayer, with adjustable lithiophobicity and electronic/ionic conductivity. This interlayer can guide lithium to deposit only on the side in contact with the lithium metal, rather than on the LNI electrolyte side. 4. **Optimize the performance of the interlayer**: By screening different carbon materials (such as carbon nanotubes CNT, carbon nanofibers CNF, etc.), CNT was identified as the most suitable material for the interlayer. Furthermore, by adjusting the CNT content (e.g., LNI-5% CNT), an interlayer with appropriate lithiophobicity and effective inhibition of lithium dendrite growth can be obtained. 5. **Theoretical simulation and experimental validation**: By combining theoretical simulations (including the Butler-Volmer equation and classical nucleation theory) with experimental results (such as electrochemical impedance spectroscopy EIS and DC polarization tests), the researchers analyzed the impact of different interlayer materials on lithium dendrite growth in detail and validated the effectiveness of the proposed interlayer design principles. In summary, this paper aims to address one of the key challenges in all-solid-state lithium-metal batteries—uncontrolled lithium dendrite growth. By carefully designing the interlayer, a stable lithium deposition/stripping process is achieved, thereby improving the overall performance and safety of the battery.

Lithium anode interlayer design for all-solid-state lithium-metal batteries

Interface design for all-solid-state lithium batteries

Interface Design for High‐Performance All‐Solid‐State Lithium Batteries

Enabling High-Areal-capacity All-Solid-state Lithium-Metal Batteries by Tri-Layer Electrolyte Architectures

Superlithiophilic, Ultrastable, and Ionic‐Conductive Interface Enabled Long Lifespan All‐Solid‐State Lithium‐Metal Batteries under High Mass Loading

In situ Triggered Rich‐LiF/Mg Multifunctional Passivation Layer for Modifying the Anode Interface of All‐Solid‐State Lithium Metal Batteries

Advanced Design of Hybrid Interfaces for High-Performance All-Solid-state Lithium Metal Batteries

The construction of multifunctional solid electrolyte interlayers for stabilizing Li6PS5Cl-based all-solid-state lithium metal batteries

Realizing the Dendrite-Free Sulfide-Based All-Solid-state Li Metal Battery by Surface Design

Ion/Electron Conductive Layer with Double-Layer-Like Structure for Dendrite-Free Solid-State Lithium Metal Batteries

A tailored dual-layer electronic shielding interface enables highly stable and dendrite-free solid-state lithium metal batteries

Suppression of lithium dendrites in all-solid-state lithium batteries by using a Janus-structured composite solid electrolyte

High Rate and Stable Solid-State Lithium Metal Batteries Enabled by Electronic and Ionic Mixed Conducting Network Interlayers

An in-situ polymerized interphase engineering for high-voltage all-solid-state lithium-metal batteries

In Situ Formation Of A Li3n-Rich Interface Between Lithium And Argyrodite Solid Electrolyte Enabled By Nitrogen Doping

High‐Areal‐Capacity and Long‐Cycle‐Life All‐Solid‐State Lithium‐Metal Battery by Mixed‐Conduction Interface Layer

Regenerative Solid Interfaces Enhance High-Performance All-Solid-State Lithium Batteries

Stable All-Solid-state Lithium Metal Batteries with Li3N-LiF-enriched Interface Induced by Lithium Nitrate Addition

High Ionic Conductive, Mechanical Robust Sulfide Solid Electrolyte Films and Interface Design for All‐Solid‐State Lithium Metal Batteries

Stabilizing Li7P3S11/lithium metal anode interface by in-situ bifunctional composite layer