Abstract:Single-crystal superalloy is the key material of turbine blade and hot end parts in aerospace field. The second generation nickel-based single crystal superalloy has been widely used because of its low cost and excellent high temperature properties. At present, the research on microstructure of superalloys at high temperature mainly depends on SEM and TEM observation after heating and loading experiment. However, such kind of work lacks real-time characterization capabilities. Carrying out in situ experiments has an important significance for understanding the real time deformation behavior and microstructure evolution of superalloys. Therefore, the development of an in situ high temperature (above 1000 degrees C) mechanical testing equipment for SEM faces huge challenges. In this work, high temperature tensile experiment at 1150 degrees C of a second generation single crystal nickel-based superalloy were carried out by means of a self-developed in situ heating tensile platform which can used in SEM. A high quality experimental data and serial SEM images were obtained in the course of tensile testing at 1150 degrees C. The analysis of force-displacement curve shows that the yield strength and fracture strength of the specimen are 580 and 620 MPa, respectively. The sequential SEM images during this research confirm that there is no obvious shape and size change for gamma and gamma' during the elastic deformation, and microstructure changing during plastic stage is mainly due to gamma phase widening which is parallel to the stress axis. The results show that the original micro-voids of samples are the weakness in high temperature tensile test at 1150 degrees C, the fracture direction is almost perpendicular to the stress axis, the crack propagated by passing the gamma' phase and through in the gamma phase, and ultimately, temperature and stress induced adjacent holes connection leading to the sample fracture.

Measurement of Grain Boundary Strength of Inconel X-750 Superalloy Using In-Situ Micro-Tensile Testing Techniques in FIB/SEM System

The Application of in Situ TEM on the Grain Boundary Brittleness of Precipitation-Strengthened Ni-based Superalloys: Recent Progress and Perspective

Effect of Grain Size on Deformation and Fracture of Inconel718: an In-Situ SEM-EBSD-DIC Investigation

In-situ Study of the Effect of Grain Boundary Misorientation on Plastic Deformation of Inconel 718 at High Temperature

Mechanical Properties of Micro-phases Along < 001 > Direction of Directionally Solidified Nickel-base Super-alloy by In-situ Nano-Indentation

In-Plane Liftout and Push-to-Pull for In Situ Mechanical Testing of Irradiated Inconel X-750

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

In-situ study of adjacent grains slip transfer of Inconel 718 during tensile process at high temperature

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

In-situ Observation of Ni-Co Based Wrought Superalloy High-Temperature Deformation: Lattice Rotation and Grain Boundary Response

In-situ SEM study of temperature-dependent tensile behavior of Inconel 718 superalloy

First-principles Computational Tensile Test on a Na-segregated Al Grain Boundary with an Si Additive and an Intergranular Embrittlement Suppression Mechanism

In-situ EBSD Study of Deformation Behavior of Inconel 740H Alloy at High-Temperature Tensile Loading

Nanoscale and Tensile-Like Properties by an Instrumented Indentation Test on PBF-LB SS 316L Steel

Atomic-scale investigation of the irradiation-resistant effect of symmetric tilt grain boundaries of Fe-Ni-Cr alloy

Investigating Bulk Mechanical Properties on a Micro-Scale: Micro-tensile Testing of Ultrafine Grained Ni–SiC Composite to Determine Its Fracture Mechanism and Strain Rate Sensitivity

In Situ Measurement of the Toughness of the Interface Between A Thermal Barrier Coating and A Ni Alloy

Investigation of In Situ 1150 ℃ High Temperature Deformation Behavior and Fracture Mechanism of a Second Generation Single Crystal Superalloy

Effect of the Grain Size on the Microtensile Deformation and Fracture Behaviors of a Nickel-Based Superalloy Via EBSD and In-Situ Synchrotron Radiation X-ray Tomography

New insights into ductility improvement of a nickel-based superalloy through grain boundary engineering

Effects of Solution Treatments on the Microstructure and Mechanical Properties of Inconel 625 Fabricated by Electron Beam Freeform Fabrication