Abstract:The gas-solid vertical single helical ribbon agitated reactor is widely used in the polypropylene industry. The gas flow and mass transfer determine the heat transfer capacity and product quality. In this work, the pressure drop was measured below and above minimum fluidization velocity (umf). Then, the axial and radial dispersion coefficients (DL and DR) were estimated below umf by measuring the step residence time distribution and the stationary radial tracer profiles, respectively. Pressure analysis show the agitation significantly reduces the bed pressure drop, changing the fixed bed below umf and bubbling bed above umf to an agitated bed with a periodic voidage. The DL was proportional to the gas velocity, with little influences of the stirring speed. The radial tracer profiles show the bed is divided by the inner diameter of the helical ribbon into the peripheral ascending region and the central descending region, without gas exchange between them. Furthermore. the tracer profiles in the descending region are classified into two types. For type I, the DR, calculated by the plug flow model with radial dispersion, is proportional to the gas velocity, with little effects of stirring speed. Type II shows uniform profiles due to the deflection of the gas flow toward the low pressure area at the inner diameter of helical ribbon. The causes of the two types are explained by the relative size of particle circulation and gas flux. These two flow regimes are quantitatively clarified with an empirical correlation of Re and Fr as flow regime transition boundary, namely dispersed plug flow and perfect mixing flow. With lower Re and higher Fr, it changes from dispersed plug flow to perfect mixing flow.

A Computational Fluid Dynamics Model Coupled with Ethylene Polymerization Kinetics for Fluidized Bed Polyethylene Reactor

Modeling of Molecular Weight and Copolymer Composition Distributions for Ethylene‐propylene Solution Copolymerization

Integration of CFD and Polymerization for an Industrial Scale Cis-Polybutadiene Reactor

Numerical Analysis of Industrial Styrene Polymerization in Nonideal Tower Reactors

CFD Modeling of Styrene Polymerization in a CSTR

Stability Analysis Of Ethylene Polymerization In A Liquid-Containing Gas-Solid Fluidized Bed Reactor

Modeling of an Industrial Polycondensation Process for Polyethylene Terephthalate

Modeling and Analysis of New Reactor Concepts for Poly(ethylene Terephthalate) Esterification Process

Effect of Temperature Switching and Dynamic Phase Equilibrium on Polymer Microstructure in Condensed-Mode Operation

Investigation of a Dynamic Operation Mode of Ethylene Polymerization Process with a Liquid-Containing Fluidized Bed

Thermal stability analysis of ethylene polymerization fluidized bed reactors under condensed mode operation through a TPM-PBM integrated model

Stability and dynamic behaviors of gas-phase ethylene polymerization process under condensed mode operation

Scale-up and Thermal Stability Analysis of Fluidized Bed Reactors for Ethylene Polymerization

Mixing Effects on the Gas Flow and Mass Transfer in a Vertical Single Helical Ribbon Agitated Reactor for Propylene Polymerization

Important Mesoscale Phenomena in Gas Phase Fluidized Bed Ethylene Polymerization

Computational Fluid Dynamics Simulation of Gas–liquid–solid Polyethylene Fluidized Bed Reactors Incorporating with a Dynamic Polymerization Kinetic Model

Modeling of the Temperature Profile in an Ethylene Polymerization Fluidized-Bed Reactor in Condensed-Mode Operation

A CFD-PBM Model Considering Ethylene Polymerization for the Flow Behaviors and Particle Size Distribution of Polyethylene in a Pilot-Plant Fluidized Bed Reactor

Modeling of the Molecular Weight Distribution and Short Chain Branching Distribution of Linear Low-Density Polyethylene from a Pilot Scale Gas Phase Polymerization Process

Operational Optimization of Polymerization Reactors with Computational Fluid Dynamics and Embedded Molecular Weight Distribution Using the Iterative Surrogate Model Method

CFD Prediction of Scale-Up Effect on the Hydrodynamic Behaviors of a Pilot-Plant Fluidized Bed Reactor and Preliminary Exploration of Its Application for Non-Pelletizing Polyethylene Process