Abstract:With increasing trends in using municipal waste incineration (MWI) technologies, more consideration has been given to the problem of harmful byproducts in its flue. In 2014, a new national standard for pollution control of municipal solid waste incineration was released by the Chinese government, which also gives guidance to local governments to establish their own standards. In order to evaluate whether the treatment technologies for MWI flue gas can both meet the new standard and have overall positive environmental impacts across whole life cycle, a waste life cycle assessment (LCA) was conducted for flue gas to compare treatment technologies employed in MWI plants. Based on a case study of a plant in Changzhou China, a model was established using three combinations of technologies: (a) Spray semi dry reactor + activated carbon + filter bag (Scenario 1); (b) Spray semi dry reactor + dry deacidification reactor + activated carbon + filter bag (Scenario 2); (c) selective non-catalytic reduction (SNCR) + spray semi dry reactor + dry deacidification reactor + activated carbon + filter bag (Scenario 3). The study has wide policy implications on how the industry is, or should be, regulated. Normalized results revealed that technologies used in Scenarios 1 and 2 had less overall impacts on the environment and less direct impact from emissions than those of Scenario 3. Energy-conservation and emission reduction index showed that Scenario 2 best fits current conditions and policy goals about energy consumption and air pollutant emission, despite recent regulations for the requirement of including SNCR in incineration plants. The most significant limiting factor is NON, which is in alignment with the results of policy analysis. Integrated analysis showed that although Scenario 2 is the best choice under current circumstances, further improvement in technology are likely to meet with new standards. Policy-makers should comprehensively consider the environmental impacts of the entire life cycle instead of the one-size-fits all standard.(C) 2018 Elsevier Ltd. All rights reserved.

Co-disposal technology for sludge and municipal solid waste based on SNCR optimization

Optimization of municipal solid waste incineration for low-NOx emissions through numerical simulation

CFD simulation of MSW combustion and SNCR in a commercial incinerator

Computational Fluid Dynamics Simulation of Combustion and Selective Non-Catalytic Reduction in a 750 T/d Waste Incinerator

The Co-Processing Combustion Characteristics of Municipal Sludge within an Industrial Cement Decomposition Furnace via Computational Fluid Dynamics

Disposal of Low Concentration Fume with Solid Waste Modified by Microwave.

Comprehensive Assessment and Optimization of a Middle-Arch Dual-Channel Municipal Solid Waste Incinerator Using Numerical Simulation Methods

Numerical Optimization Study of Combustion and Heat Transfer Characteristics in Municipal Solid Waste Incinerators

Effect of Sewage Sludge Addition on the Co-Combustion Characteristics of Municipal Solid Waste Incineration

Numerical Simulation Study on Combustion of Low Calorific Value Waste Blended with Biomass

Co-disposal kinetics and characteristics of sewage sludge and municipal solid waste incineration fly ash

Experimental Study on New Drying/Incineration Process for Sludge Treatment

Pollutant removal of a new spray drying/incineration demanstration project with capacity of 600 t/d for sludge treatment

Numerical simulation and intelligent prediction of a 500 t/d municipal solid waste incinerator

Full-Scale Plant Study of the Innovative Spray-Drying-Based Sludge Incineration (SDSI) Process: Behavior of Heavy Metals

Experimental Studies on the Combustion Characteristics of Multisource Organic Solid Waste for Collaborative Disposal Using Municipal Solid Waste Incinerators

Feasibility of sludge deep dewaterability improvement for incineration disposal by combined conditioning of freeze-thaw and sawdust

Optimization of Deposition Prevention Structure of a Grate Type Municipal Solid Waste Incinerator Based on CFD Numerical Simulation

Evaluation of Flue-Gas Treatment Technologies for Municipal Waste Incineration: A Case Study in Changzhou, China

Emission Characteristics of Polychlorinated Dibenzo-p-dioxins and Dibenzofurans from the Co-combustion of Municipal Solid Waste in a Lab-Scale Drop-Tube Furnace

Study On Sewage Sludge Fluidized Bed Incineration And Design Of 65t/D Incinerator