Abstract:Efficient and cost-effective Si-compatible lasers are a longstanding wish of the optoelectronic industry. In principle, there are two options. For many applications, lasers based on III-V compounds provide compelling solutions, even if the integration is complex and therefore costly. However, where low costs and also high integration density are crucial, group-IV-based lasers—made of Ge and GeSn, for example—could be an alternative, provided their performance can be improved. Such progress will come with better materials but also with the development of a more profound understanding of their optical properties. In this work, we demonstrate, using Ge microbridges with strain up to 6.6%, a powerful method for determining the population inversion gain and the material and optical losses of group IV lasers. This is done by deriving the values for the injection carrier densities and the cavity losses from the measurement of the change of the refractive index and the mode linewidth, respectively. We observe a laser threshold consistent with optical gain. Material loss values are obtained from a tight-binding calculation. Lasing in Ge—at steady-state—is found to be limited to low temperatures in a narrow regime of tensile strain at the crossover to the direct-band-gap band structure. We explain this observation by parasitic inter-valence-band absorption that increases rapidly with higher injection densities and temperature. N -doping seems to reduce the material loss at low excitation, but it does not extend the lasing regime. We also discuss the impact of the optically inactive carriers in the L-valley on the linewidth of group IV lasers. https://doi.org/10.1103/PhysRevResearch.4.033050 Published by the American Physical Society under the terms of the Creative Commons Attribution 4.0 International license. Further distribution of this work must maintain attribution to the author(s) and the published article's title, journal citation, and DOI. Published by the American Physical Society

Theoretical Study of Small Signal Modulation Behavior of Fabry-Perot Germanium-on-Silicon Lasers

Study of an Unsaturated PbSe QD-Doped Fiber Laser by Numerical Simulation and Experiment

InGaAsP/InP Based Q-modulated Slotted Fabry-Perot Laser Employing Lossy Half-Wave Trenches

Travelling wave analysis on high-speed performance of Q-modulated distributed feedback laser.

Analysis and Design of Combined Distributed-Feedback/fabry-perot Structures for Surface-Emitting Semiconductor Lasers

IaAsP/InGaAsP quantum-well 1.3 μm vertical-cavity surface-emitting lasers

Design and Improvement of InP-based Traveling Wave Mach-Zehnder Modulator for Monolithic Integrated with V-cavity Laser

Investigation of lasing in highly strained germanium at the crossover to direct band gap

Narrow Linewidth Single-Mode Slotted Fabry–Pérot Laser Using Deep Etched Trenches

Rate Equation Analysis of High Speed Q-Modulated Semiconductor Laser

Numerical Analysis of Semiconductor Lasers with Fbg External Cavity Reflectors

Study of Equivalent Circuit of GaN Based Laser Chip and Packaged Laser

A numerical study of picosecond laser micro-grooving of single crystalline germanium: Mechanism discussion and process simulation

Germanium based photonic components toward a full silicon/germanium photonic platform

Analysis Of Modulation Characteristics Of Widely Tunable Sampled-Grating Distributed Reflector (Sgdbr) Lasers Based On Transmission Line Laser Model

1.3 μm InAs/GaAs quantum-dot lasers grown on planar on-axis Si (001) substrates with high slope-efficiency and low differential resistance

Design of Tensile-Strained GeSn/SiGeSn Structure for Low Threshold Mid-infrared Laser Application

Theoretical Analysis and Modelling of Degradation for III–V Lasers on Si

Optimization of 1.3 Μm InAs/GaAs Quantum Dot Lasers Epitaxially Grown on Silicon: Taking the Optical Loss of Metamorphic Epilayers into Account

Ge-based photonic devices for CMOS integration (Conference Presentation)

Electrically Injected mid-infrared GeSn laser on Si operating at 140 K