Abstract:The design of cathode catalyst layer (CL) is essential to improve the mass transfer capacity of proton exchange membrane (PEM) fuel cell and increase power density. In this work, cathode CL is divided into three sub-layers, and each sub-layer is added nano-particles with different wettability. The gradient CL with hydrophilic SiO2 particles at inner layer and hydrophobic polytetrafluoroethylene (PTFE) particles at outer layer significantly enhances the performance of membrane exchange assembly (MEA). Its performance is 895 mW/cm2@0.6 V, which is 24.1 %higher than CL without any particles (721 mW/cm2@ 0.6 V). Under operating conditions of high current density, high cathode humidity and high air stoichiometry, the gradient CL has only a little voltage loss. Through Electrochemical Impedance Spectroscopies (EIS) impedance analysis under high current density (1.8A/cm2), mass transfer resistance of gradient CL is 25.4 Ω, and is much smaller than the mass transfer resistance of the homogeneous CL of 35.1 Ω, which reflects the significant enhancement in mass transfer capacity of gradient CL. The gradient catalyst layer is suitable for a wider range of current density, humidity, and stoichiometry, but excessive cathode gas stoichiometry causes a decrease in performance, which is caused by excessive drainage capacity. In addition, 18 different gradient CLs are designed and manufactured, and the gradient CL with catalyst coated membrane (CCM) structure has the best performance. In gradient CL, increasing the capillary pressure difference between sublayers is the key to performance improvement. It is confirmed that the property of MEA with appropriate wettability gradient design can be significantly improved.

Patterned Catalyst Layer Boosts the Performance of Proton Exchange Membrane Fuel Cells by Optimizing Water Management

Construction of Homogeneous Catalyst Layers at Proton Exchange Membrane Fuel Cell Cathodes

Reshaping the Cathodic Catalyst Layer for Anion Exchange Membrane Fuel Cells: from Heterogeneous Catalysis to Homogeneous Catalysis

Improving the Performance of PEM Fuel Cells: Form a Patterned Hydrophobic Catalyst Layer

Optimizing catalyst layer structure design for improved water management of anion exchange membrane fuel cells

Microscale structure optimization of catalyst layer for comprehensive performance enhancement in proton exchange membrane fuel cell

Balancing proton and mass transfers in cathode catalyst layer of high-temperature proton exchange membrane fuel cell via gradient porous structure design

Hierarchical catalyst layer structure for enhancing local oxygen transport in low Pt proton exchange membrane fuel cells

Gas Diffusion Layer with a Regular Hydrophilic Structure Boosts the Power Density of Proton Exchange Membrane Fuel Cells Via the Construction of Water Highways.

Optimizing design of catalyst layer structure with carbon-supported platinum weight ratio mixing method for proton exchange membrane fuel cells

Quadrilateral-Patterned Perforated Gas Diffusion Layers Boost the Performance of Fuel Cells

Enhanced Performance of Non-Pgm Catalysts in Air Operated PEM-fuel Cells

High-density Active Sites Porous Fe/N/C Electrocatalyst Boosting the Performance of Proton Exchange Membrane Fuel Cells

Efficient Drainage Design of Cathode Catalyst Layer for Pure Oxygen Proton Exchange Membrane Fuel Cells

Performance improvement of ultra-low Pt proton exchange membrane fuel cell by catalyst layer structure optimization

Preparation and Characterization of Nanofiber Catalyst Layer for Proton Exchange Membrane Fuel Cells

Layer-by-Layer Polydimethylsiloxane Modification Using a Two-Nozzle Spray Process for High Durability of the Cathode Catalyst in Proton-Exchange Membrane Fuel Cells

In Situ-Grown Ultrathin Catalyst Layers for Improving both Proton Exchange Membrane Fuel Cell and Anion Exchange Membrane Fuel Cell Performances

Design and optimization of gradient wettability pore structure of adaptive PEM fuel cell cathode catalyst layer

A Pt content and pore structure gradient distributed catalyst layer to improve the PEMFC performance

The Formation–Structure–Functionality Relationship of Catalyst Layers in Proton Exchange Membrane Fuel Cells