Abstract:A high advancement has been achieved in the design of proton exchange membrane fuel cells (PEMFCs) since the development of thin-film catalyst layers (CLs). However, the progress has slowed down in the last decade due to the difficulty in reducing Pt loading, especially at the cathode side, while preserving high stack performance. This situation poses a barrier to the widespread commercialization of fuel cell vehicles, where high performance and durability are needed at a reduced cost. Exploring the technology limits is necessary to adopt successful strategies that can allow the development of improved PEMFCs for the automotive industry. In this work, a numerical model of an optimized cathode CL is presented, which combines a multiscale formulation of mass and charge transport at the nanoscale (∼10nm) and at the layer scale (∼1μm) . The effect of exterior oxygen and ohmic transport resistances are incorporated through mixed boundary conditions. The optimized CL features a vertically aligned geometry of equally spaced ionomer pillars, which are covered by a thin nanoporous electron-conductive shell. The interior surface of cylindrical nanopores is catalyzed with a Pt skin (atomic thickness), so that triple phase points are provided by liquid water. The results show the need to develop thin CLs with bimodal pore size distributions and functionalized microstructures to maximize the utilization of water-filled nanopores in which oxygen transport is facilitated compared with ionomer thin films. Proton transport across the CL must be assisted by low-tortuosity ionomer regions, which provide highways for proton transport. Large secondary pores are beneficial to facilitate oxygen distribution and water removal. Ultimate targets set by the U.S. Department of Energy and other governments can be achieved by an optimization of the CL microstructure with a high electrochemical surface area, a reduction of the oxygen transport resistance from the channel to the CL, and an increase of the catalyst activity (or maintaining a similar activity with Pt alloys). Carbon-free supports (e.g., polymer or metal) are preferred to avoid corrosion and enlarge durability.

In Situ-Grown Ultrathin Catalyst Layers for Improving both Proton Exchange Membrane Fuel Cell and Anion Exchange Membrane Fuel Cell Performances

Construction of Homogeneous Catalyst Layers at Proton Exchange Membrane Fuel Cell Cathodes

Reshaping the Cathodic Catalyst Layer for Anion Exchange Membrane Fuel Cells: from Heterogeneous Catalysis to Homogeneous Catalysis

Hierarchical catalyst layer structure for enhancing local oxygen transport in low Pt proton exchange membrane fuel cells

In Situ Construction of a Nanostructured Ultrathin Catalyst Layer on Both Sides of a Membrane toward Fuel Cell Application

Ultrathin Ultralow-Platinum Catalyst Coated Membrane for Proton Exchange Membrane Fuel Cells

Performance improvement of ultra-low Pt proton exchange membrane fuel cell by catalyst layer structure optimization

Ultrathin Nanoporous Metal Electrodes Facilitate High Proton Conduction for Low-Pt PEMFCs

Semi-ordered catalyst layer with ultra-low Pt loading for proton exchange membrane fuel cells

Engineering Triple‐Phase Boundary in Pt Catalyst Layers for Proton Exchange Membrane Fuel Cells

Engineering the Catalyst Layers Towards Enhanced Local Oxygen Transport of Low-Pt Proton Exchange Membrane Fuel Cells: Materials, Designs, and Methods

Recent progresses and remaining issues on the ultrathin catalyst layer design strategy for high-performance proton exchange membrane fuel cell with further reduced Pt loadings: A review

On the optimal cathode catalyst layer for polymer electrolyte fuel cells: Bimodal pore size distributions with functionalized microstructures

Electrospun Catalyst Layers Using Short-Side-chain Ionomer for Low Platinum and High Performance PEMFCs

Nanostructured Ultrathin Catalyst Layer Based on Open-Walled Ptco Bimetallic Nanotube Arrays for Proton Exchange Membrane Fuel Cells

Pore-scale Study of Reactive Transport Processes in Catalyst Layer Agglomerates of Proton Exchange Membrane Fuel Cells

Optimizing catalyst layer structure design for improved water management of anion exchange membrane fuel cells

Patterned Catalyst Layer Boosts the Performance of Proton Exchange Membrane Fuel Cells by Optimizing Water Management

A Pt content and pore structure gradient distributed catalyst layer to improve the PEMFC performance

Bridging the gap between highly active oxygen reduction reaction catalysts and effective catalyst layers for proton exchange membrane fuel cells

Balancing proton and mass transfers in cathode catalyst layer of high-temperature proton exchange membrane fuel cell via gradient porous structure design