Abstract:High durability of proton exchange membrane fuel cells (PEMFCs) is one main objective of this technology nowadays. Among different ways, the use of a superhydrophobic catalyst layer in the cathode may help to increase the stability of the cell under operation. Superhydrophobic cathodic layers improve water management in the cell by enhancing the back-diffusion transport from cathode to anode. As a consequence, anode humidification is favored whereas flooding of the cathode is avoided, leading to higher cell response at intermediate and high current densities [1]. Superhydrophobic catalyst layers can be obtained by adding specific agents to the precursor ink that is later deposited together with the catalyst and the ionomer. Another possibility is the use of electrospray deposition, which does not require additives. Electrospray is a dry deposition method where the ink is deposited under an electric field, yielding particular ionomer distribution inside the pores of the layer as a consequence of electrostatic interactions. Accelerated stress tests (AST) are well stablished protocols to analyze durability of PEMFCs in a systematic and reduced time frame [2]. Protocols for stressing different components of the cell have been proposed. In this work, different cell configurations have been mounted, using electrosprayed catalyst layers in cathode, anode, and both. The cells have been submitted to an AST that affects mainly the cathodic catalyst layer. The study is complemented with microscopy analysis (cross-sectional) and local mechanical properties (small-punch) (Fig. 1). The results show the effect of superhydrophobic cathodic catalyst layers on the durability of a PEMFC. Acknowledgements Funding by PORHYDRO2 project (TED2021-131620B-C22, ‘Preparation and characterisation of catalyst layers fabricated by electrospray for proton exchange fuel cells with passive gas feed’) by the Spanish Ministry of Science and Innovation. [1] M.A. Folgado, J.J. Conde, P. Ferreira-Aparicio, A.M. Chaparro, Single Cell Study of Water Transport in PEMFCs with Electrosprayed Catalyst Layers, Fuel Cells. 18 (2018) 602–612. https://doi.org/10.1002/fuce.201700217. [2] S. Stariha, N. Macauley, B.T. Sneed, D. Langlois, K.L. More, R. Mukundan, R.L. Borup, Recent Advances in Catalyst Accelerated Stress Tests for Polymer Electrolyte Membrane Fuel Cells, J. Electrochem. Soc. 165 (2018) F492–F501. https://doi.org/10.1149/2.0881807jes. [3] R. Hernández, S. Merino, D. Plaza, L. Duque, M.A. Folgado, A.M. Chaparro, M. Serrano, G. de Diego, Study of Mechanical Properties of Membrane-Electrode Assemblies for Proton Exchange Membrane Fuel Cells By the Small-Punch Technique, ECS Meet. Abstr. MA2022-02 (2022) 1426–1426. https://doi.org/10.1149/ma2022-02391426mtgabs. Figure 1

Improving the Performance of PEM Fuel Cells: Form a Patterned Hydrophobic Catalyst Layer

Construction of Homogeneous Catalyst Layers at Proton Exchange Membrane Fuel Cell Cathodes

Reshaping the Cathodic Catalyst Layer for Anion Exchange Membrane Fuel Cells: from Heterogeneous Catalysis to Homogeneous Catalysis

High-Performance Proton Exchange Membrane Fuel Cells Enabled by Highly Hydrophobic Hierarchical Microporous Carbon Layers Grafted with Silane

Hierarchical catalyst layer structure for enhancing local oxygen transport in low Pt proton exchange membrane fuel cells

Layer-by-Layer Polydimethylsiloxane Modification Using a Two-Nozzle Spray Process for High Durability of the Cathode Catalyst in Proton-Exchange Membrane Fuel Cells

The Performance Improvement of Membrane and Electrode Assembly in Open-Cathode Proton Exchange Membrane Fuel Cell

The buffer microporous layer improved water management for proton exchange membrane fuel cell at varying humidification

Patterned Membranes for Proton Exchange Membrane Fuel Cells Working at Low Humidity

Effect of Superhydrophobic Catalyst Layers on PEMFC Durability

Optimizing catalyst layer structure design for improved water management of anion exchange membrane fuel cells

Hydrophobic modification enhances the microstructure stability of the catalyst layer in alkaline polymer electrolyte fuel cells

Designing self-humidifying proton exchange membrane fuel cells by using patterned acid-alkaline hybrid cathodes

Design of graded cathode catalyst layers with various ionomers for fuel cell application

On the optimal cathode catalyst layer for polymer electrolyte fuel cells: Bimodal pore size distributions with functionalized microstructures

Microscale structure optimization of catalyst layer for comprehensive performance enhancement in proton exchange membrane fuel cell

Water management improvement in PEM fuel cells via addition of PDMS or APTES polymers to the catalyst layer

Optimizing design of catalyst layer structure with carbon-supported platinum weight ratio mixing method for proton exchange membrane fuel cells

Performance Enhancement of Polymer Electrolyte Membrane Fuel Cells with a Hybrid Wettability Gas Diffusion Layer

Balancing proton and mass transfers in cathode catalyst layer of high-temperature proton exchange membrane fuel cell via gradient porous structure design

Design and optimization of gradient wettability pore structure of adaptive PEM fuel cell cathode catalyst layer