Abstract:As the most basic interconnection metallic material, copper (Cu) has been widely used in giant-large scale integrated circuits (GLSI). Corrosion inhibitors always play a crucial role in the Cu chemical mechanical polishing (CMP) process. The passivation of hydrogen peroxide (H2O2) alone is too weak to adequately protect against chemical corrosion on the surface of Cu film, thus, it is necessary to add corrosion inhibitors to the slurry. As a representative corrosion inhibitor, 1, 2, 4-triazole was compared with a novel corrosion inhibitor known as TT-LYK (ethanol, 2, 2′-[[(methyl-1H-benzotriazol-1-yl) methyl] imino] bis-), and their mixed inhibitor was studied in this paper. Different analytical methods such as the potentiodynamic polarization test, physical appearance phenomenon analysis, contact angle measurement and dynamic polishing experiment were used to compare their inhibition properties, and the fitting of different adsorption isotherms and static erosion tests were used to clarify the adsorption types and passivation processes respectively. The results indicated that both TT-LYK and 1, 2, 4-triazole achieved the goal of inhibiting Cu surface corrosion, but the inhibition effect of TT-LYK was slightly weaker at the same mass fraction. The corrosion protection of the two inhibitors is mainly attributable to the presence of organic inhibitor molecules on the surface of Cu by chemisorption and physisorption simultaneously. The passivation processes of both can be divided into two steps. First, the direct growth of the Cu-inhibitor passivation film occurs, followed by the redeposition of the Cu-inhibitor complex. From the results of electrochemical experiments, it can be concluded that the structure of the thin passivation film growing on the Cu surface varies with the inhibitor, and the composition of the passivation film was investigated by XPS and Raman spectrum analysis. At the same time, the surface roughness after polishing was found to decrease with the increase in inhibition effect of the inhibitors. According to the inhibition characteristics of these two inhibitors, a mixed corrosion inhibitor (TT-LYK and 1, 2, 4-triazole) was proposed in this study. Under the synergistic inhibition action, better inhibition effect and surface quality for Cu CMP were obtained. This outcome may be ascribed to the variation in the structure and density of the passivation film.

Eco-friendly Corrosion Inhibitors for Multilevel Metal Interconnects of Integrated Circuits

Study on Effective Methods and Mechanism of Inhibiting Cobalt Removal Rate in Chemical Mechanical Polishing of GLSI Low-Tech Node Copper Film

Effect of Corrosion Inhibitor and Non-ionic Surfactant on CMP of Cu/Co Barrier Stack

Selection and Optimization of Corrosion Inhibitors for Improved Cu CMP and Post-Cu CMP Cleaning

A Low Cost and Residue-Free Abrasive-Free Copper Cmp Process with Low Dishing, Erosion and Oxide Loss

The Effect of Inhibitors on the Electrochemical Deposition of Copper Through-silicon Via and its CMP Process Optimization

Electrochemical Corrosion Behavior and Theoretical Simulation of Cobalt in Chemical Mechanical Polishing Process

Slurry System Establishment and Optimization for Advanced Cobalt Interconnect Metallization

The Role of Dipotassium Ethylenediaminetetraacetic Acid and Potassium Oleate on Chemical Mechanical Planarization Relevant to Heterogeneous Materials of Cobalt Interconnects

Study on CMP of Copper Interconnect with Novel Mo-Based Diffusion Barriers

Study on the film forming mechanism, corrosion inhibition effect and synergistic action of two different inhibitors on copper surface chemical mechanical polishing for GLSI

Chemical Interactions and Mechanisms of Different Ph Regulators on Copper and Cobalt Removal Rate of Copper Film CMP for GLSI

Corrosion Inhibiting Effect on Copper Chemical Mechanical Planarization (cmp) in Fe(No3)(3) Based Slurries

Bioinspired corrosion inhibition for printed circuit board: implications of dendritic Sn-ZIF-LIS coating on Cu metal

Research Progress of Organic Corrosion Inhibitors in Metal Corrosion Protection

Corrosion Inhibiting Effect on Copper Chemical Mechanical Planarization (CMP) in Fe(NO<sub>3</sub>)<sub>3</sub> Based Slurries

Rational Utilization of the Size and Electronic Effect of Inhibitors Enabling High Polishing Rate with Minimum Corrosion in Copper Chemical Mechanical Polishing

Selecting Alternative Metals for Advanced Interconnects

Green Chemical Mechanical Polishing of Copper with 2,5-Dihydroxy-1,4-dithianeas As the Inhibitor: Experimental and Theoretical Studies

Sustainable Corrosion Inhibitors for Copper and its Alloys

Evaluation and Mechanism Study of a Novel Green Chemical Mechanical Polishing Slurry for Cobalt Interconnects