Abstract:As the most basic interconnection metallic material, copper (Cu) has been widely used in giant-large scale integrated circuits (GLSI). Corrosion inhibitors always play a crucial role in the Cu chemical mechanical polishing (CMP) process. The passivation of hydrogen peroxide (H2O2) alone is too weak to adequately protect against chemical corrosion on the surface of Cu film, thus, it is necessary to add corrosion inhibitors to the slurry. As a representative corrosion inhibitor, 1, 2, 4-triazole was compared with a novel corrosion inhibitor known as TT-LYK (ethanol, 2, 2′-[[(methyl-1H-benzotriazol-1-yl) methyl] imino] bis-), and their mixed inhibitor was studied in this paper. Different analytical methods such as the potentiodynamic polarization test, physical appearance phenomenon analysis, contact angle measurement and dynamic polishing experiment were used to compare their inhibition properties, and the fitting of different adsorption isotherms and static erosion tests were used to clarify the adsorption types and passivation processes respectively. The results indicated that both TT-LYK and 1, 2, 4-triazole achieved the goal of inhibiting Cu surface corrosion, but the inhibition effect of TT-LYK was slightly weaker at the same mass fraction. The corrosion protection of the two inhibitors is mainly attributable to the presence of organic inhibitor molecules on the surface of Cu by chemisorption and physisorption simultaneously. The passivation processes of both can be divided into two steps. First, the direct growth of the Cu-inhibitor passivation film occurs, followed by the redeposition of the Cu-inhibitor complex. From the results of electrochemical experiments, it can be concluded that the structure of the thin passivation film growing on the Cu surface varies with the inhibitor, and the composition of the passivation film was investigated by XPS and Raman spectrum analysis. At the same time, the surface roughness after polishing was found to decrease with the increase in inhibition effect of the inhibitors. According to the inhibition characteristics of these two inhibitors, a mixed corrosion inhibitor (TT-LYK and 1, 2, 4-triazole) was proposed in this study. Under the synergistic inhibition action, better inhibition effect and surface quality for Cu CMP were obtained. This outcome may be ascribed to the variation in the structure and density of the passivation film.

Green Chemical Mechanical Polishing of Copper with 2,5-Dihydroxy-1,4-dithianeas As the Inhibitor: Experimental and Theoretical Studies

A Low Cost and Residue-Free Abrasive-Free Copper Cmp Process with Low Dishing, Erosion and Oxide Loss

Mechanisms of Mixed Corrosion Inhibitors in Copper Chemical Mechanical Polishing

Study on the film forming mechanism, corrosion inhibition effect and synergistic action of two different inhibitors on copper surface chemical mechanical polishing for GLSI

Roles and mechanistic analysis of adenine as a green inhibitor in chemical mechanical polishing

The Effect of Inhibitors on the Electrochemical Deposition of Copper Through-silicon Via and its CMP Process Optimization

Experimental and Computational Investigation of Complexing Agents on Copper Dissolution for Chemical Mechanical Polishing Process

Roles and mechanism analysis of chitosan as a green additive in low-tech node copper film chemical mechanical polishing

Experimental and Computational Investigation of Salicylhydroxamic Acid as a Corrosion Inhibitor for Copper in Alkaline Solutions

Chemical processes in the chemical mechanical polishing of copper

Chemical Mechanical Planarization of Copper Using Ethylenediamine and Hydrogen Peroxide Based Slurry

Environment friendly chemical mechanical polishing of copper

An Efficient and High Quality Chemical Mechanical Polishing Method for Copper Surface in 3D TSV Integration

Angstrom surface on copper induced by novel green chemical mechanical polishing using ceria and silica composite abrasives

Copper chemical mechanical polishing using a slurry-free technique

Tribo-chemical Behavior of Copper in Chemical Mechanical Planarization

Experimental and computational studies on TAD as an additive of copper chemical mechanical polishing

Chemical mechanical polishing for copper films in integrated circuit wiring layers using an advanced slurry

Chemical Roles on Cu-slurry Interface During Copper Chemical Mechanical Planarization

Investigation on the Mechanisms of Corrosion Inhibitor 5-aminotetrazole Used in the Copper Chemical Mechanical Polishing

Tribocorrosion Study of Copper During Chemical Mechanical Polishing in Potassium Periodate-Based Slurry