Abstract:<p>Ultrafine-grained (UFG) materials produced by severe plastic deformation methods generally exhibit a higher strength, but a lower uniform ductility. In this paper, an UFG Al–Zn–Mg–Cu alloy was fabricated via cross accumulative extrusion bonding (CAEB) and subsequent aging to achieve high strength and moderate uniform elongation. The influences of CAEB and subsequent aging on microstructure and tensile properties of the alloy were investigated. After CAEB, TEM characterization revealed that the microstructure exhibited typically ED-elongated ultrafine grains (740 ± 20 nm). Post-CAEB aging led to the formation of many nano-sized particles with different morphologies. These particles precipitated in the grain interiors and at grain boundaries, among which the main strengthening phase was η′ phase. EBSD characterization showed that the fraction of high angle grain boundaries increased to 61.0% for the post-CAEB aged alloy. At the same time, microtexture was significantly weakened as the CAEB process was applied to the alloy. The main texture components were mainly composed of Cu and S as well as a small amount of Brass and Cube. In addition, the tensile test at room temperature demonstrated that the post-CAEB aged sample possessed a high ultimate tensile strength of 562 MPa while simultaneously maintaining a moderate uniform elongation of 21.5%.</p>

Strong and Ductile Al–Zn–Mg–Zr Alloy Obtained by Equal Angular Pressing and Subsequent Aging

Mechanical Properties and Microstructure of Al–Mg–Mn–Zr Alloy Processed by Equal Channel Angular Pressing at Elevated Temperature

Ultrafine-grained Al–Zn–Mg–Cu alloy processed via cross accumulative extrusion bonding and subsequent aging: Microstructure and mechanical properties

Improvement of Strength and Ductility of Mg-Zn-Ca-Mn Alloy by Equal Channel Angular Pressing

Microstructure and Mechanical Properties of Mg–Zn–Ca Alloy Processed by Equal Channel Angular Pressing

Microstructure characteristics of an ultra-high strength extruded Al-4.7Cu–1Li-0.5Mg-0.1Zr–1Zn alloy during heat treatment

Achieving High Strength and High Electrical Conductivity in a CuCrZr Alloy Using Equal-Channel Angular Pressing

Microstructure and Tensile Properties of A Mg-Zn-Y-Zr Alloy Containing Quasicrystal Phase Processed by Equal Channel Angular Pressing

Microstructure and Mechanical Properties of Ultrafine Grained Mg97Y2Zn1 Alloy Processed by Equal Channel Angular Pressing

Superplastic Behavior of Ultrafine-Grained Aluminum-Based Alloy Processed by ECAP

Fine-grained Mg–1Mn–0.5Al–0.5Ca–0.5Zn alloy with high strength and good ductility fabricated by conventional extrusion

Ultra-high strength Al-Zn-Mg-Cu alloys with high zinc content prepared via powder hot extrusion

Achieving superior strength and ductility synergy in bulk ultrafine grained Al-Mg-Sc-Zr alloy via powder pre-aging

Achieving ultrahigh specific strength of an ultrafine grained Mg-9Li-1Al alloy via the combined processing of ECAP with repeated annealing and rolling

Microstructural Characteristics and Mechanical Properties of Extruded Al-4Cu-1Li-0.4Mg-0.1Zr-xZn Alloy

Improving Strength and Ductility of Mg–Gd–Y–Zn–Zr Alloy Simultaneously Via Extrusion, Hot Rolling and Ageing

Micro/nanostructure high strength and high conductivity CuCrZr alloy prepared through equal channel angular pressing and aging treatment

Microstructure and Mechanical Properties of Mg96Y3Zn1 Alloy Processed by Equal Channel Angular Pressing

High Strength Mg_(97)Y_2Zn_1 Alloy Processed by Extrusion and Equal Channel Angular Pressing

Precipitation behaviors and mechanical properties of a solution-treated Mg-Gd-Nd-Zn-Zr alloy during equal-channel angular pressing process

Effect of the Equal Channel Angular Pressing on the Microstructure and Phase Composition of a 7xxx Series Al-Zn-Mg-Zr Alloy