Abstract:HR3C steel is an austenitic high-temperature-resistant steel. Because of its good strength and high-temperature performance, it has been widely used in ultra-supercritical power plant boilers. With the increasingly frequent start-up and shutdown of thermal power units, leakages of HR3C steel pipes have occasionally occurred due to the embrittlement of HR3C pipe steel after a long service duration. In this study, the embrittlement mechanisms of HR3C pipe steel are investigated systematically. The mechanical properties of the pipe steel after running for 70,000 h in an ultra-supercritical unit were determined. As a comparison, the pipe steel supplied in the same batch was aged at 700 degrees Celsius for 500 h. The mechanical properties and the micro-precipitation of the aged counterparts were also determined for comparison. The results show that the embrittlement of HR3C pipe steel in service for 70,000 h is obvious. The average impact absorption is only 5.5 J, which is a decrease of 96.7%. It is found that embrittlement of HR3C steel also occurs after 500 h of aging at 700 °C, and the average value of impact absorption energy decreases by 70.4%. The comparison experiment between the in-service pipe steel and the aged pipe steel shows that in the rapid decline stage of the impact toughness of HR3C steel, the M23C6 carbide in the microstructure has a continuous chain distribution in the grain boundary. There were no other precipitated phases observed. The rapid precipitation and aggregation of M23C6 carbides leads to the initial embrittlement of HR3C steel at room temperature. The CRFe-type σ phase was found in the transmission electron microscope (TEM) image of the steel pipe after 70 thousand hours of use. The precipitation of the σ phase further induces the embrittlement of HR3C pipe steel after a long service duration.

Research on the Application of Thermoelectric Potential Technology in Austenitic Heat-resistant Steel During Aging

DSI-based Studies of the Effects of High-temperature Aging on Local Mechanical Properties of HR3C/T92 Dissimilar Steel Welded Joint

Microstructures and Mechanical Properties of a Newly Developed Austenitic Heat Resistant Steel

Deterioration of Mechanical Properties of Novel Constructional Steel Material at Elevated Temperatures

Microstructural Evolution of TP347H After Post Weld Heat Treatment and Aging

Microstructure Characteristics and Their Effects on the Mechanical Properties of As-Served HR3C Heat-Resistant Steel

Effect of heat treatment on microstructure and mechanical properties of S31042 austenite heat resistant steel

The Microstructure and Mechanical and Corrosion Behaviors of Thermally Aged Z3CN20-09M Cast Stainless Steel for Primary Coolant Pipes of Nuclear Power Plants

The Effect of Aging Heat Treatment on the Microstructure and Mechanical Properties of 10cr20ni25mo1.5nbn Austenitic Steel

Research Progress of HR3C Heat Resistant Steel Used in Ultra Supercritical Boiler

Multiphase Strengthening of Nanosized Precipitates in a Cost‐Effective Austenitic Heat‐Resistant Steel

Microstructure-Property Relationship and Embrittlement Mechanism of HR3C Steel with High-Temperature Service of 65000 h

Embrittlement Mechanisms of HR3C Pipe Steel at Room Temperature in Ultra-Supercritical Unit

Effect of microstructural evolution on high-temperature strength of 9Cr-3W-3Co martensitic heat resistant steel under different aging conditions

Exploring the Improvement of Strength and Cryogenic Impact Toughness in Hot-Rolled High Mn Austenitic Steel for Cryogenic Application

Experimental Study on Thermal Aging Impact Properties of Austenitic Stainless Steel Z3CN20.09M

Study on Intelligent Classification of Aging Heat-Resistant Materials

Effect of Heat Treatment Parameters on the Modification of Nano Residual Austenite of Low-Carbon Medium-Chromium Steel

Precipitation Evolution in the Austenitic Heat-Resistant Steel HR3C upon Creep at 700 °C and 750 °C

Corrosion of an Austenitic Heat-Resistant Steel HR3C in High-Temperature Steam and Supercritical Water

Study on Microstructure Evolution and Properties of SA738Gr.B Steel with Different Austenitizing Holding Time and Peak Temperature