Abstract:Phase change phenomena in microchannels have been projected as an effective option for thermal management of various microscale systems. However, for the design of heat sinks which utilize these phenomena, a clear understanding of the physical mechanisms involved, in the microscale domain, is required. In the present study, a numerical simulation is carried out to predict the characteristics of two phase flow with liquid to vapor phase change, in rectangular microchannels for a range of hydraulic diameters. The annular flow pattern, reported to be the most common in microchannel, has been investigated, with water as the flowing medium. The analysis considers, among other parameters, the effect of surface tension on the flow dynamics, which could be significant in microchannels. The mathematical model is numerically solved using a quasi-three dimensional approach, incorporating the variations in the cross-sectional areas of both the phases along the flow direction. Since it is expected that the continuum approximation may be insufficient in the vapor domain in channels of very small dimensions, an analysis incorporating slip flow at the liquid vapor interface analysis has been performed, where the channel dimensions produce Knudsen number values in the range 0.001–0.1, as suggested in the literature. The liquid film thickness along the flow direction is determined utilizing mass conservation, and the velocity distributions at different locations along the flow direction are obtained by solving the governing differential equations numerically. The two phase pressure drop is calculated for cases demanding slip and no slip conditions. A comparison has been made of the fluid flow characteristics, between the slip and no slip cases for the cases where slip flow is expected. The effects of the imposed heat flux, volume flow rate and channel geometry on the velocity distribution and pressure drop are examined. The predicted pressure drop values are found to increase with increasing heat flux, and decrease with an increase in the flow rate and the channel height. The two phase heat transfer coefficient and the wall temperature of the channel are also determined. The two phase heat transfer coefficient is found to increase with an increase in the vapor quality. It is also noticed that the wall temperature decreases along the length of the channel and the wall temperature at the exit of the channel decreases with decrease in volume flow rate, within the range of parameters used, which is in accordance with observations reported in the literature. The results are found to be in good agreement with the experimental and theoretical results available in the literature.

Numerical simulation of meniscus evaporation in microchannel based on diffuse interface method

Comparison of Different Analytical Models for Heat and Mass Transfer Characteristics of an Evaporating Meniscus in a Micro-Channel

Numerical Simulation of Thermocapillary Flow Induced by Non-Uniform Evaporation on the Meniscus in Capillary Tubes

Numerical investigation of heat and mass transfer from an evaporating meniscus in a heated open groove

Numerical analysis of variation of capillary evaporating meniscus profile with different operating condition

On Numerical Simulation Techniques of Stable Crack Growth

Modeling And Numerical Simulations Of Vapor-Liquid Flow And Heat Transfer Within Microchannel Heat Sinks

Numerical Study of Conjugated Heat Transfer in Evaporating Thin-Films Near the Contact Line

A Numerical Investigation on Micro Particle Dynamics Near an Evaporating Meniscus

Numerical Simulation for Heat Transfer and Fluid Flow Performances of Thin Film Evaporation in the Micro Rectangular Groove

A Mesoscopic Approach for Nanoscale Evaporation Heat Transfer Characteristics

Numerical simulation of liquid film formation and its heat transfer through vapor bubble expansion in a microchannel

Numerical Investigation on Fluid Flow Characteristics of Thin Film Evaporation Meniscus Region in the Rectangular Groove

Characteristics of an Evaporating Thin Film in a Microchannel

New Boundary Conditions for the Evaporating Thin-Film Model in A Rectangular Micro Channel

Research on Interfacial Characteristics of Ethanol Evaporation in Single Microchannels Using Visualization and Infrared Thermography

A Numerical Investigation on the Marangoni Stability Under a Convex Meniscus in a Vertical Micro Channel

Capillary-assisted Flow and Evaporation Inside Circumferential Rectangular Micro Groove

Three-Dimensional Numerical Simulation for Annular Condensation in Rectangular Microchannels

Effect of working fluid on heat transfer of evaporating extended meniscus in capillary channel

Study on Flow Characteristics of Working Medium in Microchannel Simulated by Porous Media Model