Abstract:The mechanical behavior of a commercially pure titanium (CP-Ti) is systematically investigated in quasi-static (Instron, servohydraulic) and dynamic (UCSD's recovery Hopkinson) compression. Strains over 40% are achieved in these tests over a temperature range of 77–1000K and strain rates of 10−3–8000/s. At the macroscopic level, the flow stress of CP-Ti, within the plastic deformation regime, is strongly dependent on the temperature and strain rate, and displays complex variations with strain, strain rate, and temperature. In particular, there is a three-stage deformation pattern at a temperature range from 296 to 800K, the specific range depending on the strain rate. In an effort to understand the underlying mechanisms, a number of interrupted tests involving temperature jumps are performed, and the resulting microstructures are characterized using an optical microscope. Based on the experimental results and simple estimates, it is concluded that the three-stage pattern of deformation at temperatures from 296 to 800K, is a result of dynamic strain aging, through the directional diffusion of dislocation-core point defects with the moving dislocation at high strain rates, although the usual dynamic strain aging by point defects segregating outside the dislocation core through volume diffusion is also observed at low strain rates and high temperatures. The microscopic analysis shows that there is substantial deformation twinning which cannot be neglected in modeling the plastic flow of CP-Ti. The density of twins increases markedly with increasing strain rate, strain, and decreasing temperature. Twin intersections occur, and become more pronounced at low temperatures or high strain rates. In sum, the true stress–true strain curves of CP-Ti show two stages of deformation pattern at low temperatures, three stages at temperatures above 296K, and only one stage at temperatures exceeding 800K, although all three stages may exist even at 1000K for very high strain rates, e.g. 8000/s. While the dislocation motion is still the main deformation mechanism for plastic flow, the experimental results suggest that dynamic strain aging should be taken into account, as well as the effect of deformation twinning.

Response of Ti6321 Titanium Alloy at Different Strain Rates under Tensile Loading

Superior Strain Rate Strengthening Effect and Ductility of a Ti-4.5Al-2.9V-3Fe Alloy under High Strain Rate Loading

Strain-Rate-Dependent Tensile Response of Ti–5Al–2.5Sn Alloy

Mechanical properties and deformation mechanisms of a commercially pure titanium

Effect of Microstructure on High-Speed Tensile Mechanical Properties of Ti-1300 Alloy

Deformation Behavior of Ti-6Al-3Nb-2Zr-1Mo Titanium Alloy at Low Temperatures and High Strain Rates

Enhanced Mechanical Property of Ti-45551 Alloy Due to TRIP Effect

Strain rate sensitivity and strain hardening exponent during the isothermal compression of Ti60 alloy

Strain Rate Effects on the Mechanical Behavior of Porous Titanium with Different Pore Sizes

Research on Dynamic Compression Properties and Deformation Mechanism of Ti6321 Titanium Alloy

The Microstructures and Deformation Mechanism of Hetero-Structured Pure Ti under High Strain Rates

Dynamic Strain-Rate Effect On Uniaxial Tension Deformation Of Ti5al2.5sn Alpha-Titanium Alloy At Various Temperatures

Strain Rate Effects on Tensile Deformation Behaviors of Ti-10V-2Fe-3Al Alloy Undergoing Stress-Induced Martensitic Transformation

Strain Rate Sensitivity of Tensile Properties in Ti–47Al–2Mn–2Nb–0.8TiB2 Alloy

The Mechanical Response and Failure Mechanism of a Near Α Titanium Alloy under High-Strain-rate Compression at Different Temperatures

Strain Rate Sensitivity of Tensile Properties in Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy: Experiments and Constitutive Modeling

Effects of Strain Rate and Strain on Microstructural Evolution and Mechanical Properties of a Ti-10 At.%al Alloy

Microstructure evolvement of isometry TiAl under tensile impact loadings

Effect of Strain Rate and Temperature on the Deformation Behavior in a Ti-23.1Nb-2.0Zr-1.0O Titanium Alloy

Mechanical Response and Deformation Mechanisms of TB17 Titanium Alloy at High Strain Rates

High strain rate mechanical behavior of Ti-6Al-4V with micro–macro correlation under compressive loading