Abstract:Al-Zn alloys exhibited lower reaction temperature and micro-explosion phenomenon when compared to Al which benefited from the low melting point and boiling point of Zn. To further improve the energetic performance of Al-Zn alloys, Mg with low reaction temperature was originally incorporated into Al-Zn alloys via centrifugal atomization. The addition of Mg results in the production of Mg32(Al,Zn)49 with the low melting point and stepwise oxidation, which can effectively improve the reactivity and combustion. The results show that the prepared Al-Zn-Mg alloys display uniform particle size distribution, regular morphology, and excellent sphericity, which are composed of α-Al and Mg32(Al,Zn)49 compounds. The initiation oxidation temperature of AlZn10Mg5 and AlZn10Mg10 alloy powders is lower than that of AlZn10 alloy powders, and the oxidation efficiency is higher than that of AlZn10 alloys, which may be attributed to the oxidation of Mg32(Al,Zn)49. Adding Mg to the AlZn10 alloy significantly increases the peak pressure and pressurization rate during combustion. In the meanwhile, Al-Zn-Mg alloys burn faster, more intensely, and more completely when compared to AlZn10 alloys. The combustion of the spherical AlZn10Mg10 alloy powders is the most intense visually. It can be ascribed that during the combustion, a large amount of melt and gas breaks through the oxide layer, increasing the contact intimacy between oxygen and the alloy, which can significantly shorten the combustion time. In summary, the spherical AlZn10Mg5 and AlZn10Mg10 alloy powders prepared in this study show promising applications in fuels with high reactivity and better combustion performance.

Spherical Al-Zr alloy powders prepared by centrifugal atomization for tunable energetic behavior

Tuning Ignition and Energy Release Properties of Zirconium Powder by Atomic Layer Deposited Metal Oxide Coatings

High-quality Spherical Zirconium Alloy Powders Prepared by Thermal Plasma Treatment for Additive Manufacturing

Oxidation and Ignition of a Heterogeneous Al-Zn Alloy Powder Metallic Fuel

Promising Fuels for Energetics: Spherical Al-Li Powders with High Reactivity Via Incorporation of Li

Improved Ignition and Combustion Performance of Al-Zn-Mg Ternary Alloys by Incorporating Mg into Al-Zn Alloys

(Feal3)(1-X)Zr-X Amorphous Alloys Prepared By Mechanical Alloying

Preparation of Ti6Al4V Powder with High Yield of Fine Particle by Crucible-less Gas Atomization Technology

Preparation of Zr50Cu40Al10 amorphous powder by mechanical alloying and its crystallization behaviors

Preparation and Reaction Characteristics of Spherical Al-Si Alloy Fuel

Kinetics and Combustion Behavior of Atomized Zn-Mg Alloy Powder

Pressureless Sintering Behaviour of Al2O3/ZrO2 Amorphous/solid Solution Powder with Ultra-Fine ZrO2 Nanoparticle Precipitation

Fabrication of spherical W–ZrC powder for additive manufacturing by spray granulation combined with plasma spheroidization

In-situ Assembly of Al-Li-Si Alloy Powders with Enhanced Thermal Stability and Tailored Combustion

Characterization of U–Nb–Zr dispersion fuel prepared by centrifugal atomization process

Preparation Of Zta Powders By Spray Granulation And Properties Of Sintered Zta Composites

Fabrication and Stability of Ultrafine ZrC Nanoparticles Dispersion Strengthened Sub-Micrometer Grained W Alloy

Study on a novel Al-B-Li alloy powder with high enthalpy of combustion

Amorphous Mechanism of Zr50Al15Ni10Cu25 Amorphous Alloy Powder Prepared by Mechanical Alloying

Research on Zr50Al15Ni10Cu25bulk Amorphous Alloys Prepared by Mechanical Alloying and Low Pressure Sintering

Research on preparation process for the in situ nanosized Zr(Y)O2 particles dispersion-strengthened tungsten alloy through synthesizing doped hexagonal (NH4)0.33·WO3