Abstract:Statement of problem. The accuracy of digital scanning for complete dental arch and implant-supported complete-arch restorations has been reported. However, research addressing the accuracy of digital scanning methods for complete-arch tooth preparation is lacking. Purpose. The purpose of this in vitro study was to compare the accuracy of intraoral scanning, impression scanning, and cast scanning for complete-arch preparation.Material and methods. Maxillary and mandibular jaw typodonts with 28 teeth prepared for complete crowns were used as reference casts and digitized as reference data sets with a desktop scanner. Three digital scanning methods were applied. First, the reference casts were each scanned 10 times with an intraoral scanner to generate the intraoral scanning group data sets. Second, the reference casts were each captured 10 times by using polyvinyl siloxane impression material, and the impressions were scanned with a desktop scanner to generate the impression scanning group data sets. Third, the impressions obtained in the impression scanning group were used to make gypsum casts which were then digitized with a desktop scanner to generate the cast scanning group data sets. Accuracy was determined by trueness and precision. Three-dimensional deviations of the prepared arches and anterior and posterior segments were measured from root mean square values and depicted on color-difference maps. Differences among test groups were analyzed by using a 1-way ANOVA and the post hoc Bonferroni test for normally distributed data or the Kruskal-Wallis test with Bonferroni correction for non-normally distributed data (a=.05).Results. The trueness of the maxillary arch was significantly higher in the impression scanning group than in the cast scanning and intraoral scanning groups (P<.05), but no significant differences were found among the 3 groups of the mandibular arch (P>.05). The precision of both arches was significantly higher in the impression scanning and intraoral scanning groups than in the cast scanning group (P<.05). Color maps showed horizontal symmetrical displacement in the intraoral scanning group relative to the reference data sets and within-group unilateral distal-end distortion. Irregular arch deformations were noted in the impression scanning group, and buccal and occlusal expansion occurred in the anterior-posterior direction in the cast scanning group. Pooled data for anterior teeth indicated that the trueness was lowest in the intraoral scanning group; however, that for the maxillary anterior teeth did not differ, while that for the mandibular anterior teeth differed significantly among groups (P<.05). For the posterior teeth, deviation was the lowest in the impression scanning group, and significant differences were noted in both arches among the 3 groups (P<.05).Conclusions. Of the methods tested, impression scanning was the most accurate for the creation of a digital cast of a complete prepared arch. (J Prosthet Dent 2022;128:1001-8)

Preparing guiding planes for removable partial dentures: an in vitro comparison between assisted CAD-CAM template procedure and freehand preparation

In vitro comparison of guide planes for removable partial dentures prepared with CAD-CAM-assisted templates, guiding rod templates, and freehand

Comparison of Four CAD-CAM Guides for Preparing Guiding Planes of Removable Partial Dentures

Template‐aided and freehand guiding plane preparation for removable partial dentures: A randomized controlled trial

3D Evaluation of Accuracy of Tooth Preparation for Laminate Veneers Assisted by Rigid Constraint Guides Printed by Selective Laser Melting.

A metal template for preparing guiding planes for removable partial dentures

Preliminary Application and Evaluation of Digital Step-by-step Tooth-Preparation Templates

Accuracy of Computer-Guided Implant Surgery by a CAD/CAM and Laser Scanning Technique.

Enhancing Fixed Partial Denture Pontic Fabrication: An In Vitro Comparative Study of the Digital and Manual Techniques

3D Printing of Drill Guide Template for Access Cavity Preparation in Human Molars: a Preliminary Study

A Novel Computer-Aided Design/Computer-Assisted Manufacture Method for One-Piece Removable Partial Denture and Evaluation of Fit.

Accuracy of a Chairside Fused Deposition Modeling 3D-Printed Single-Tooth Surgical Template for Implant Placement: an in Vitro Comparison with a Light Cured Template

Accuracy of Three Digital Scanning Methods for Complete-Arch Tooth Preparation: an in Vitro Comparison

[Evaluation of Production and Clinical Working Time of Computer-Aided Design/computer-Aided Manufacturing (CAD/CAM) Custom Trays for Complete Denture].

Novel Method of Fabricating Individual Trays for Maxillectomy Patients by Computer-Aided Design and Rapid Prototyping.

Trueness of 3D printed partial denture frameworks: build orientations and support structure density parameters

Preliminary Clinical Application of Removable Partial Denture Frameworks Fabricated Using Computer-Aided Design and Rapid Prototyping Techniques.

[Initial Evolution Research for Design and Process Accuracy of One Type of Domestic Computer Aided Design Soft and Computer Aided Manufacture].

The Accuracy of a Novel 3D Digital Evaluation Method of Intraoral Fitness for Removable Partial Dentures.

Accuracy of Tooth Positioning in 3D-Printing Aided Manufactured Complete Dentures: an in Vitro Study.

Comparison of selective laser melting and stereolithography etching templates for guided endodontics