Abstract:Statement of problem. The accuracy of digital scanning for complete dental arch and implant-supported complete-arch restorations has been reported. However, research addressing the accuracy of digital scanning methods for complete-arch tooth preparation is lacking. Purpose. The purpose of this in vitro study was to compare the accuracy of intraoral scanning, impression scanning, and cast scanning for complete-arch preparation.Material and methods. Maxillary and mandibular jaw typodonts with 28 teeth prepared for complete crowns were used as reference casts and digitized as reference data sets with a desktop scanner. Three digital scanning methods were applied. First, the reference casts were each scanned 10 times with an intraoral scanner to generate the intraoral scanning group data sets. Second, the reference casts were each captured 10 times by using polyvinyl siloxane impression material, and the impressions were scanned with a desktop scanner to generate the impression scanning group data sets. Third, the impressions obtained in the impression scanning group were used to make gypsum casts which were then digitized with a desktop scanner to generate the cast scanning group data sets. Accuracy was determined by trueness and precision. Three-dimensional deviations of the prepared arches and anterior and posterior segments were measured from root mean square values and depicted on color-difference maps. Differences among test groups were analyzed by using a 1-way ANOVA and the post hoc Bonferroni test for normally distributed data or the Kruskal-Wallis test with Bonferroni correction for non-normally distributed data (a=.05).Results. The trueness of the maxillary arch was significantly higher in the impression scanning group than in the cast scanning and intraoral scanning groups (P<.05), but no significant differences were found among the 3 groups of the mandibular arch (P>.05). The precision of both arches was significantly higher in the impression scanning and intraoral scanning groups than in the cast scanning group (P<.05). Color maps showed horizontal symmetrical displacement in the intraoral scanning group relative to the reference data sets and within-group unilateral distal-end distortion. Irregular arch deformations were noted in the impression scanning group, and buccal and occlusal expansion occurred in the anterior-posterior direction in the cast scanning group. Pooled data for anterior teeth indicated that the trueness was lowest in the intraoral scanning group; however, that for the maxillary anterior teeth did not differ, while that for the mandibular anterior teeth differed significantly among groups (P<.05). For the posterior teeth, deviation was the lowest in the impression scanning group, and significant differences were noted in both arches among the 3 groups (P<.05).Conclusions. Of the methods tested, impression scanning was the most accurate for the creation of a digital cast of a complete prepared arch. (J Prosthet Dent 2022;128:1001-8)

Accuracy of Three Digital Scanning Methods for Complete-Arch Tooth Preparation: an in Vitro Comparison

Influence of scan extension and starting quadrant on the accuracy of four intraoral scanners for fabricating tooth-supported crowns

In vitro comparative study between complete arch conventional implant impressions and digital implant scans with scannable pick-up impression copings

Accuracy of Impressions for Multiple Implants: A Comparative Study of Digital and Conventional Techniques

Complete-arch Accuracy of Intraoral Scanners.

A new method for the evaluation of the accuracy of full-arch digital impressions in vitro

Coordinate-based data analysis of the accuracy of five intraoral scanners for scanning completely dentate and partially edentulous mandibular arches

Influence of scanning protocol on the accuracy of complete-arch digital implant scans: An in vitro study

Accuracy of edentulous full‐arch implant impression: An in vitro comparison between conventional impression, intraoral scan with and without splinting, and photogrammetry

Accuracy of full arch three-dimensional dentition models from intraoral scanners

Evaluation of the Accuracy of Digital Impression Techniques Based on an Integrated ADA Model

Comparing the accuracy of full-arch implant impressions using the conventional technique and digital scans with and without prefabricated landmarks in the mandible: An<i> in</i><i> vitro</i> study

Trueness of 4 sectional-cast digital methods for transferring the interocclusal relationship in complete mouth rehabilitation.

Accuracy of Intraoral Digital Impressions for Whole Upper Jaws, Including Full Dentitions and Palatal Soft Tissues

Accuracy and Reproducibility of Virtual Edentulous Casts Created by Laboratory Impression Scan Protocols.

Accuracy of photogrammetric imaging versus conventional impressions for complete arch implant-supported fixed dental prostheses: A comparative clinical study

Accuracy of intraoral versus desktop scanners used in digitizing polyvinyl siloxane impression for fabricating a CAD‐CAM customized post and core

Comparisons of precision and trueness of digital dental casts produced by desktop scanners and intraoral scanners

A Comparison of Full Arch Trueness and Precision of Nine Intra-Oral Digital Scanners and Four Lab Digital Scanners

Scanning Accuracy of 10 Intraoral Scanners for Single-crown and Three-unit Fixed Denture Preparations: an in Vitro Study.

Study of scanning repeatability of intraoral digital impressions