Abstract:Na‐free solution‐processed CISSe solar cells present inferior performance due to the poor crystallinity of the absorber. By NaCl pre‐selenization treatment (Pre‐ST), the crystallinity of the submicron CISSe absorber significantly improves and grain boundaries remarkably decrease compared to the Na‐free absorber. Such high‐quality submicron CISSe absorber shows improved PV performance. Low‐cost solution‐processed CuIn(S,Se)2 (CISSe) has great potential for large‐scale production of photovoltaics (PV). However, low power conversion efficiency caused by poor crystallinity is one of the main drawbacks compared to vacuum‐processed CISSe solar cells. In this work, three strategies for sodium (Na) incorporation into solution‐processed CISSe by soaking in sodium chloride (NaCl) aqueous‐ethanol solution [1 molarity (M) for 10 minutes (min)], either prior to absorber deposition (pre‐deposition treatment, Pre‐DT), before selenization (pre‐selenization treatment, Pre‐ST), or after selenization (post‐selenization treatment, PST) are researched. The Pre‐ST CISSe solar cells achieve a better PV performance than those from the other two strategies of Na incorporation. For optimization, soaking times (5, 10, and 15 min) and NaCl concentrations (from 0.2 to 1.2 m) of the Pre‐ST are researched. The highest efficiency achieved is 9.6% with an open‐circuit voltage (Voc) of 464.5 mV, a short‐circuit current density (jsc) of 33.4 mA cm−2, and a fill factor (FF) of 62.0%. Compared to the reference CISSe solar cell, Voc, jsc, FF, and efficiency of the champion Pre‐ST CISSe device are improved absolutely by 61.0 mV, 6.5 mA cm−2, 9%, and 3.8%, respectively. Simultaneously, the open‐circuit voltage deficit, the back contact barrier, and the bulk recombination are found to be reduced for Pre‐ST CISSe.

High-performance sub-micron CIGSSe solar cells optimized for sodium doping by adjusting diffusion barriers

Efficiency improvement for post-sulfurized CIGS solar cells enabled by in situ Na doping

Sodium control in Ultrathin Cu(In,Ga)Se2 solar cells on transparent back contact for efficiencies beyond 12%

Passivation of Grain Boundaries and Defects in CZTSSe Solar Cells by In Situ Na Doping

Optimization of CuInGaSSe properties and CuInGaSSe/CdS interface quality for efficient solar cells processed with CuInGa precursors

Developments of High-Efficiency Flexible Cu(In,Ga)Se 2 Thin Film Solar Cells on a Polyimide Sheet by Sodium Incorporation

Defect Passivation in Cu2ZnSnSe4 Thin-Film Solar Cells by Novel Sodium Doping

Na-doping-induced Modification of the Cu2ZnSn(S,Se)4/CdS Heterojunction Towards Efficient Solar Cells

Sodium Doping of Solution-Processed Cu2ZnSn(S,Se)4 Thin Film and Its Effect on Cu2ZnSn(S,Se)4 Based Solar Cells

Effects of Alkali Elements on Copper Indium Gallium Aluminum Selenide Flexible Solar Cells Fabricated on Polyimide Substrates

Sodium Doping Effects on the Crystalline and Electrical Properties of Cu2znsnse4 Thin Films

Sodium Passivation of the Grain Boundaries in CuInSe2 and Cu2ZnSnS4 for High-Efficiency Solar Cells

Synergistic Effect of Na and Se on CZTSe Solar Cells Through a Soft Chemical Process

High Efficiency Cu(In,Ga)Se_2 Thin-Film Solar Cells Doped Na on Polyimide Substrate

Sodium Incorporation for Performance Improvement of Solution‐Processed Submicron CuIn(S,Se)2 Thin Film Solar Cells

The Multiple Roles of Na Ions in Highly Efficient CZTSSe Solar Cells

Improving the Crystallization and Carrier Recombination of Cu2ZnSnS4 Thin Film Deposited on Mo-coated Soda-Lime Glass by Extra Sodium Doping Through Solution Process

Adjustment of Alkali Element Incorporations in Cu(In,Ga)Se2 Thin Films with Wet Chemistry Mo Oxide As a Hosting Reservoir

Effects of Na Doping on the Distribution of Elements and the Formation of Back Surface Field in CIGS Absorption Layer

Alkali Metals Doping for High-Performance Planar Heterojunction Sb2S3 Solar Cells

Alkali Metal Pretreatment for Precise Na Doping and V oc Improvement in CIGS Thin-Film Solar Cells