Abstract:The texture distribution, tensile property and fracture toughness of 7050 aluminum alloy thick plate were investigated by optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffractometry, tensile and toughness tests. The results show that the microstructure,texture,tensile property and fracture toughness are inhomogeneous in different layers along the thickness direction. At the same thickness, the tensile property and fracture toughness show appreciable anisotropy. From the surface to the center, the average sizes of the coarse second phase particles and recrystallization grains increase. Near the surface of the plate,typical shear textures {111}110 and cube textures {001}100 are observed, while the center of the plate shows typical β fiber texture with a scattering of cube texture. The quarter layer of the plate seems to serve as a transition layer. From the surface to the center, the strength is inhomogeneous in the rolling direction and long transverse direction. The strength in the center is smaller than that on the surface of the plate. The strength and fracture toughness show appreciable anisotropy at the same thickness. The strength in the rolling direction is higher than that in the long transverse direction and the short transverse direction, and the fracture toughness in the L-T orientation is higher than that in the T-L and S-L orientations at the same thickness. The fracture mode in the L-T orientation is trangranular fracture, and in the S-L orientation the fracture mode is intergranular fracture. In the T-L orientation, the fracture mode is a mixed fracture, the fraction of the trangranular fracture is lower than that in the L-T orientation, and the fraction of the intergranular fracture is lower than that in the S-L orientation.

Micro Porosity and Its Effect on Fatigue Performance of 7050 Aluminum Thick Plates

Characterization of Fracture and Fatigue Behavior of 7050 Aluminum Alloy Ultra-thick Plate

Fracture Toughness and Fatigue Crack Growth Analysis of 7050-T7451 Alloy Thick Plate with Different Thicknesses

Novel Quantification of Porosity Defects on Fatigue Behavior for Cast Aluminum-Silicon Alloys by X-ray Micro-Tomography

Metallographic Characterization of Porosity in A Cast Aluminum Alloy A356-T6

Fatigue Fracture Characteristic of 7050-T7451 High-Strength Aluminum Alloy Thick Plate

Effect of Microstructural Features on Fatigue Behavior in A319-T6 Aluminum Alloy

Effect of Porosity on Fatigue Property in Aluminum Cast Alloys

Effect Of Roughness On Fatigue Life Of Open Holes

Fatigue Behavior and Microscopic Mechanism of 7020 Aluminum Alloy Profile

Analysis of Microporosity-Dependent Fatigue Crack Behavior in Alloy 718 by Using Synchronic Radiation X-Ray CT and FEM

Fatigue performance of 7475-T7351 aluminum alloy plate

Mechanism of Precipitate Microstructure Affecting Fatigue Behavior of 7020 Aluminum Alloy

The Role of Microstructure and Local Crystallographic Orientation Near Porosity Defects on the High Cycle Fatigue Life of an Additive Manufactured Ti-6Al-4V

Effect of Shrinkage Versus Hydrogen Pores on Fatigue Life of Cast AlSi11Mg Alloy

On high‐cycle fatigue anisotropy of an aluminum alloy super‐thick plate

Effect of Solution Treatment on the Microstructure and Fatigue Properties of 7050 Aluminum Alloy

Inhomogeneity of Texture, Tensile Property and Fracture Toughness of 7050 Aluminum Alloy Thick Plate

Effect of surface integrity on fatigue life of 7075-T6 aluminum alloy by combination of fine turning with hydrostatic deep rolling

Effect of Microstructure on Fatigue Damage Accumulation in 7075 Aluminum Alloy Subjected to a Single Compressive Overload

Fatigue Characteristic of Aluminum Alloy Plates with Different Thickness