Abstract:A range of Fe-Cr-Ni alloys are used in nuclear power plants due to their high mechanical strength and corrosion resistance. As a major component of these alloys, Ni contributes to the formation of austenite microstructures. In many nuclear reactor applications the alloys are exposed to ionizing radiation (g-rays) that can continuously decompose water to a range of highly redox active species (such as •OH, H2O2, O2). The change in water chemistry induced by radiation can affect both the general and localized corrosion behaviour of these alloys. In particular, its influence on the susceptibility of an alloy to localized corrosion such as crevice and stress corrosion cracking (SCC) are important for assessment of reactor component aging. As well, corrosion products that dissolve into the reactor coolant can be transported to the reactor core where they can be neutron activated. This can create a radiological hazard for reactor maintenance personnel. Thus, quantifying the rate of general corrosion and the corrosion product transport in a reactor are important safety, operation and maintenance issues. It has been well established that the type of oxide that forms on a surface is a critical factor in determining both general and localized corrosion behaviour. Both alloy composition and water chemistry affect the type of oxide that forms. Systematic studies that examine the effect of alloy composition on corrosion are rare and those available have been conducted mostly from a metallurgical perspective. There are even fewer studies that examine the combined effects of alloy composition and corrosion environment. A fundamental understanding of the mechanism by which the Fe to Ni ratio in a steel alloy influences the corrosion rate in different environments will provide valuable information that can be used for alloy selection and usage. We have investigated the effect of the Fe to Ni ratio of alloy on oxide formation and growth kinetics. For this study, customized steel alloys with different Ni contents and constant Cr content (18 ± 1 %) were prepared. The Ni content ranged from 15 to 25 wt.%, within the range between AISI 316L and Alloy 800 (Fig. 1). The corrosion kinetics was investigated using a combination of coupon corrosion tests and electrochemical measurements. These measurements were augmented by oxide surface and depth analyses using several spectroscopic and imaging techniques, and by post-test solution analyses for dissolved metal loss. We found that the oxide formed at pH 10.6 and 80 °C has a graded layer structure, consisting of a mixed spinel oxide (FeCr2O4/Fe3O4/NiFe2O4) as an inner layer and Ni(OH)2 as an outer layer. The increase in Ni content from 15 to 25 wt.% does not affect the inner layer but increases the thickness of the Ni(OH)2 layer. The increase in Ni content also decreases the total amount of dissolved metal loss. Gamma-irradiation of the corroding system increases the corrosion potential on these alloys. Correspondingly, gamma-radiation accelerates the formation of passive oxide layers and decreases the overall rate of metal dissolution. The observed kinetics of oxide growth and metal dissolution can be explained by the competition kinetics of oxide growth and dissolution for oxidized metals. Figure 1

Insight on Corrosion Behavior of a Cu–P–Cr–Ni Steel with Different Ni Contents by Electrochemical and Periodic Immersion Corrosion Experiments

Influence of Ni Addition on Corrosion Performance of Medium-temperature Filler Metal with Low Cu Content for Al Brazed Joints

Substitution of Ni with Cu and Its Impact on the Corrosion Resistance of Ni-Advanced Weathering Steels in the Simulated Tropical Marine Atmosphere

Effects of Cu on the corrosion resistance of heat-treated weathering steel in a marine environment

High Corrosion-Resistant Ni–P/Ni/Ni–P Multilayer Coatings on Steel

Corrosion Behaviors of TWIP Steels in NaCl Solution

Electrochemical Impedance Spectra for the Corrosion of Porous Cu-35mass%Ni-(5,10)mass%Cr Alloys in Molten (0.62li,0.38k)2co3 at 650 °C in Air

Clarifying the effect of Cu element on the corrosion properties of Ni-Mo low alloy steel in marine environment

Effect of Nickel Content on the Corrosion Behaviour of Stainless Steel at 80 °C

Influence of Carbon Content on Corrosion Resistance Performance of Weathering Steel

Investigation of Microstructure and Corrosion Behavior of Weathering Steel in Aqueous Solution Containing Different Anions for Simulating Service Environments

Corrosion Behavior of Copper Bearing Steels and the Derived In-Situ Coating

[Articular manifestations of aphthosis (Behcet's syndrome)].

Effect of Ni on the oxidation behavior of corrosion products that form on low alloy steel exposed to a thin electrolyte layer environment

Effects of Cr and Ni on the microstructure and corrosion resistance of high-strength low alloy steel

Long-Term Corrosion Behavior of Cu-10Ni and Cu-20Ni Alloys in Simulated Seawater

Corrosion Processes of Weathering Steels in 2.0% Nacl Neutral Solutions

In Situ Thermal Interactions of Cu-Based Anti-Corrosion Coatings on Steel Implemented by Surface Alloying

Insight to corrosion mechanism of 90/10 copper-nickel alloys under different sea depths

On how the corrosion behavior and the functions of Cu, Ni and Mo of the weathering steel in environments with different NaCl concentrations

Effect of Ni on Corrosion Fatigue Properties of Medium Carbon High Strength Spring Steel