Abstract:TiAl intermetallic alloys have attracted considerable attention in aerospace applications over the last few decades owing to their low density and superior mechanical properties at high temperatures. However, these alloys are also known as difficult-to-machine materials that hinder efficient manufacturing. This study presents a systematic investigation on the machinability of TiAl alloys with three types of microstructures obtained by different heat treatment parameters. These were classified as near-gamma (NG), duplex (DP), and fully lamellar (FL). The machinability was evaluated based on the cutting forces and machined surface roughness. The material with α2/γ lamellar structures (FL) exhibited the lowest cutting force (3.21 N). However, produced a rougher surface (80 nm Ra) as compared to the NG microstructure (4.69 N and 47 nm Ra). Electron backscattering diffraction (EBSD) evaluation of the primary deformation zone in the cutting chips revealed that insufficient heat energy was converted from plastic deformation for recrystallization or β+γ→α2 phase transformation to occur. This indicated that the deformation mechanisms were significantly dependent upon the plasticity. The NG microstructure demonstrated a higher degree of plasticity in the primary deformation zone, which was attributed to the combined effect of super-dislocation decomposition, ordinary dislocation slip, and refined mechanical twins with preferred orientation along the < 11 2 ¯ > {111} crystallographic orientation. Conversely, the FL microstructure exhibited brittleness during chip formation due to the weak bonding force between hexagonal α2 and tetragonal γ phases that led to preferential micro-cracking along each interface. Reducing the crystal orientation is conductive for improving machined surface quality. The notion of enhanced brittleness to explain the reduction in cutting forces due to the dissipation of energy through fracture was supported with numerical simulations. Microscopic evaluation was used to understand the deformation differences of the equiaxed γ grain and α2/γ lamellar microstructure during micro-cutting. Additionally, enhanced the understanding of the deformation mechanism of these multi-phase alloys.

Material Removal Behavior of Nanoscale Shear Cutting and Extrusion Cutting of Monocrystalline Γ-Tial Alloy

Numerical simulation of nano-cutting behaviors for polycrystalline γ-TiAl alloy: The effect of grain sizes

Atomic simulation for the effect of nano-cutting parameters on the 3D surface morphology of polycrystalline γ-TiAl alloy

A Study on Material Removal Caused by Phase Transformation of Monocrystalline Silicon During Nanocutting Process Via Molecular Dynamics Simulation

Wear mechanism of diamond-cutting tool in nano-cutting polycrystalline γ-TiAl alloy based on molecular dynamics simulation

Molecular Dynamics Analysis Micro-Mechanism Of Ductile Machining Single Crystal Silicon By Means Of Nanometric Cutting Technology

Molecular dynamics simulation of the effect of tool parameters on nano-cutting of polycrystalline γ-TiAl alloys

Effect of cryogenic nano-cutting on surface integrity of the single crystal γ-TiAl alloy via atomic simulation

Nanocutting mechanisms of Cu50Zr50 amorphous alloy: A molecular dynamics simulation

Molecular dynamics simulation for temperature assisted machining of a polycrystalline γ-TiAl alloy

Acoustic Emission Response to Nano-Cutting Process of Monocrystal gamma-TiAl Alloy via Atomistic Simulation

Effect of Repeated Nanocutting on Surface Quality and Subsurface Damage of Γ-Tial Alloy

Material deformation mechanism of polycrystalline tin in nanometric cutting

Nano-cutting deformation characteristics and atomic-scale behavior of two-phase γ/γ′ nickel-based single crystal superalloy

Modelling and experimental investigation on nanometric cutting of monocrystalline silicon

Atomic Simulation of Effect of Stress-Relief Annealing on the Regulation of Residual Stress in Nano-cutting of γ-TiAl Alloy

Effects of Material Properties on Micro-Scale Cutting of TA15 Alloy and Network-Structured TiBw/TA15 Composites

Cutting simulation capabilities based on crystal plasticity theory and discrete cohesive elements

Effect of cutting parameters on the depth of subsurface deformed layers of single γ-TiAl alloy during nano-cutting process

Investigation on the surface damage mechanism of single-crystal γ-TiAl alloy with pore defects based on nanocutting

Microstructural modulation of TiAl alloys for controlling ultra-precision machinability