Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes (d) were used for two-stage tensile tests under the conditions with distinct pre-strain & epsilon;pre and intersection angle & theta;SPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing & epsilon;pre and & theta;SPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d. This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre -strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

Study on Damage Evolution Beneath Spherical Indenter Through Experiments and Mechanism-Based Strain Gradient Crystal Plastic Simulations

Atomistic Simulation of Nanoindentation on Incipient Plasticity and Dislocation Evolution in Γ/γ′ Phase with Interface and Void

Influence of Defects and Crystallographic Orientation on Mechanical Behavior of Nanocrystalline Aluminium

Indentation Creep Surface Morphology of Nickel-Based Single Crystal Superalloys

Microdamage In Polycrystalline Ceramics Under Dynamic Compression And Tension

Microstructure- and Damage-Nucleation-based Crystal Plasticity Finite Element Modeling for the Nucleation of Multi-Type Voids During Plastic Deformation of Al Alloys

Experimental and Finite Element Study of Void Growth in Nickel-Base Single Crystal Superalloys

Micro-failure of metals under inhomogeneous plastic deformation

Molecular Dynamics Investigation of Loading Orientation Effect on Dynamic Behaviors of Void in Aluminum

A crystal plasticity-based microdamage model and its application on the tensile failure process analysis of 7075 aluminum alloy

Crystal Plasticity Based Investigation of the Effects of Additive Manufactured Voids on the Strain Localization Behaviour of Ti-6al-4v

Deformation-Induced Surface Roughening of an Aluminum–Magnesium Alloy: Experimental Characterization and Crystal Plasticity Modeling

Atomic Simulation of Void Effect on the Microstructure Evolution and Internal Stress Transmission in Nanoindentation

A unified model for yield strength and plastic behavior of nanovoid evolution in tungsten based on molecular dynamics simulations

Crystal Plasticity Modeling and Neutron Diffraction Measurements of a Magnesium AZ31B Plate: Effects of Plastic Anisotropy and Surrounding Grains

Crystal Plasticity Based Investigation of Micro-Void Evolution under Multi-Axial Loading Conditions

Crystal Plasticity-Based Analysis and Modelling of Grain Size and Strain Path Dependent Micro-Scaled Deformation Mechanisms of Ultra-Thin Sheet Metals

Grain size and orientation affected deformation inhomogeneity and local damage of hot-deformed Al-Zn-Mg alloy

Experimental and Computational Study of Microstructural Effect on Ductile Fracture of Hot-Forming Materials

Plastic Strain Accommodation and Crack Initiation in a Randomly-Oriented Mg-8y-1zr Magnesium Alloy During Accumulated Tensile Deformation

Evolution of spherical nanovoids within copper polycrystals during plastic straining: Atomistic investigation