Abstract:During deformation of aluminum (Al) alloys, there are three kinds of voids being formed by distinct mechanisms, i.e., matrix-cracking voids (MCVs), particle-cracking voids (PCVs), and interface-debonding voids (IDVs), due to mesoscale heterogeneous deformation. The three kinds of void nucleation have different effects on the subsequent void growth, void coalescence, and ductile fracture of Al alloys. To determine the complex nucleation behavior of the three kinds of voids under mesoscale heterogeneous deformation, a microstructure- and damage-nucleation-based crystal plasticity finite element (MDNCPFE) model considering different nucleation mechanisms was established. To realize the MDN-CPFE modeling, the deformation and void nucleation of the matrix, particle, and their interface in Al alloys were described by a non-local dislocation density CP constitutive model and a local stored energy density criterion, an elastic constitutive model and a maximum principal stress criterion, and a cohesive zone model and fracture energy criterion, respectively. The developed MDN-CPFE model was validated by the nucleation locations and quantitative variations of the three kinds of voids in an in-situ tensile test. Using the developed model, the nucleation characteristics of the three kinds of voids during the small deformation of Al alloys were analyzed. It is found that PCVs are likely to nucleate within particles that are located at the deformation bands and with greater shape irregularity; IDVs are prone to nucleate at the interfaces around smaller particles in the deformation bands; MCVs tend to nucleate within grains with a higher Schmid factor and aspect ratio. The void area fractions (VAFs) of the three kinds of voids all evolve with an incubation stage and then followed by an exponentially increasing stage during deformation. The duration of the incubation stage for the three kinds of voids, designated by the nucleation strain, presents the following sequence: PCV < IDV < MCV; while, their VAFs and quantities present the opposite sequence. Additionally, the effects of the particle volume fraction and grain size on the nucleation strain, total VAF, and proportion of VAFs of the three kinds of voids were unraveled.

Influence of Defects and Crystallographic Orientation on Mechanical Behavior of Nanocrystalline Aluminium

Exploration of the Defect’s Effect on the Mechanical Properties of Different Orientated Nanowires

Orientation Effects on the Tensile Properties of Single Crystal Nickel with Nanovoid: Atomistic Simulation

Atomic Simulation of the Effect of Orientation on Tensile/compressive Properties in Nickel-Based Single Crystal Superalloys

Microstructure Characterization and Damage Coupled Constitutive Modeling of Nickel-Based Single-Crystal Alloy with Different Orientations

Atomistic Simulation Analysis of the Effects of Void Interaction on Void Growth and Coalescence in a Metallic System

Molecular Dynamics Investigation of Loading Orientation Effect on Dynamic Behaviors of Void in Aluminum

Effects of Crystalline Orientation, Twin Boundary and Stacking Fault on the Crack-Tip Behavior of a Mode I Crack in Nanocrystalline Titanium

Atomic Simulation of Void Location Effect on the Void Growth in Nickel-Based Single Crystal

Molecular Dynamics Study on Mechanical Behaviors of Ti/Ni Nanolaminate with a Pre-Existing Void

Effect of Crystallographic Orientation on Nano-indentation Behavior of Nickel Based Single Crystal Super Alloys

Molecular Dynamics Study of Uniaxial Deformation in Perfect and Defective Aluminum

Microstructure- and Damage-Nucleation-based Crystal Plasticity Finite Element Modeling for the Nucleation of Multi-Type Voids During Plastic Deformation of Al Alloys

Influence of Orientation on Crack Propagation of Aluminum by Molecular Dynamics

Numerical simulation on creep damage and crack initiation behaviour of nickel-based single crystal superalloys containing a casting void

Molecular dynamics study of void effect on nanoimprint of single crystal aluminum

Crystal Plasticity-Based Micromechanical Finite Element Modelling of Ductile Void Growth for an Aluminium Alloy under Multiaxial Loading Conditions

Study on the uniaxial tensile mechanical behavior of two-dimensional single-crystal aluminum nitride

Crystallographic Orientation and Spatially Resolved Damage in a Dispersion-Hardened Al Alloy

Atomic Simulation of Deformation Behavior of Dual-Phase Crystalline/amorphous Mg/Mg-Al Nanolaminates

Effect of crystallographic orientation on mechanical properties of single-crystal CoCrFeMnNi high-entropy alloy