Abstract:The newly designed alloy compositions for selective laser melting (SLM) have aroused great interest. In this study, zirconium modified Al-Cu-Mg alloys were fabricated by SLM. Results show that crack-free samples with relative density of nearly 100% were obtained by optimizing the processing parameters. With the increase of scanning speed, the relative density decreases due to insufficient energy input. In addition, the microstructure transforms from homogeneous to bio-modal, the reason is the unstable flows caused by the high scanning speed. The small hatching space will provide more energy input and preheat, leading to the coarse surface. Introduction Additive Manufacturing (AM) processes enable to fabricate parts with very complex shape[1]. Selective laser melting (SLM), one of the preferred AM techniques, has recently gained considerable attention due to high manufacturing flexibility, nearnet-shape production and efficient use of raw material[2, 3]. Al-Cu-Mg alloy has become an attractive material due to the low density, high fracture toughness and fatigue strength[4, 5]. Nowadays, processing high strength aluminum alloys by SLM is confronted with great difficulties because of its poor flowability, high reflectivity, high thermal conductivity, large solidification range and hot cracking susceptibility[6]. Therefore, the biggest stumbling block to the application of high strength aluminum in SLM is the hot crack. To expand the scope of aluminum alloys suiting for SLM, new high strength aluminum alloys are urgent to be investigated. Recently, scandium (Sc), zirconium (Zr), titanium (Ti) and vanadium (V) have been proved as the effective microalloying element for aluminum alloys to improve the weldability and mechanical properties[7-9]. Nowadays, the addition of microalloying element has been applied to SLM aluminum alloys to improve their formability. The microstructural evolution, densification, properties and heat treatment of Al-Mg-Sc-Zr fabricated by SLM have been investigated[10-13]. Zhang H et al.[14] have found that the Zr modified Al-Cu-Mg parts with ultrafine grain exhibits better mechanical properties and broader processing window. However, the effect of processing parameters on the Zr modified Al-Cu-Mg alloy has not been studied. 1246 Solid Freeform Fabrication 2018: Proceedings of the 29th Annual International Solid Freeform Fabrication Symposium – An Additive Manufacturing Conference Reviewed Paper

Towards understanding metallurgical defect formation of selective laser melted wrought aluminum alloys

Effect of Processing Parameters on the Densification of an Additively Manufactured 2024 Al Alloy

Numerical Study of the Pore Defects Formation Mechanisms in Selective Laser Melting Process

Microstructure, metallurgical defects and hardness of Al–Cu–Mg–Li–Zr alloy additively manufactured by selective laser melting

Cracking Behavior, Microstructure and Properties of Selective Laser Melted Al-Mn-Mg-Sc-Zr Alloy

Defect Formation Mechanisms in Selective Laser Melting: A Review

Role of defects on the high cycle fatigue behavior of selective laser melted Al–Mg–Sc–Zr alloy

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Damage Mechanisms in Selective Laser Melted AlSi10Mg under As Built and Different Post-Treatment Conditions

A review on the simulation of selective laser melting AlSi10Mg

Effect of Laser Parameters on Microstructure, Metallurgical Defects and Property of AlSi10Mg Printed by Selective Laser Melting

Microstructural Evolution and Defect Formation in a Powder Metallurgy Nickel-Based Superalloy Processed by Selective Laser Melting

Effects of Defects and Microstructures on Tensile Properties of Selective Laser Melted Ti6Al4V Alloys Fabricated in the Optimal Process Zone

A review of selective laser melting of aluminum alloys: Processing, microstructure, property and developing trends

The effect of processing parameter on zirconium modified Al-Cu-Mg alloys fabricated by selective laser melting

Cracking criterion for high strength Al–Cu alloys fabricated by selective laser melting

Influence of Modified Microstructures and Characterized Defects on Tensile Properties and Anisotropy of Selective Laser Melting-Produced Ti6Al4V Alloys

POROSITY DEVELOPMENT AND CRACKING BEHAVIOR OF Al-Zn-Mg-Cu ALLOYS FABRICATED BY SELECTIVE LASER MELTING

The crack and pore formation mechanism of Ti–47Al–2Cr–2Nb alloy fabricated by selective laser melting

Selective Laser Melting of High Strength Al–Cu–Mg Alloys: Processing, Microstructure and Mechanical Properties

Direct Manufacturing of Cu-based Alloy Parts by Selective Laser Melting