Abstract:Although the use of 3D printing in civil engineering has grown in popularity, one of the primary challenges associated with it is the absence of steel bars inside the printed mortar. As a result, developing 3D printing mortar with ultra-high compressive, flexural, and tensile strengths is critical. In the present study, an ultra-high-performance mortar incorporating silica fume (SF) and graphene nanoplatelets (GNPs) was developed for 3D printing application. The concrete mixture added SF to the concrete mixture in the range between 0% and 20%, while GNPs were added as a partial replacement by cement weight from 0.5% to 2%. The flowability and the machinal properties of the proposed mortar, including compressive (CS), tensile (TS), and flexural strength (FS), were investigated and assessed. Microstructure analysis involving FESEM and EDX was also investigated and evaluated, while response surface methodology (RSM) was considered to predict and optimize the optimum value of GNPs and SF. Workability results show that the flowability is reduced when the amount of graphene increases. Based on the predicted and experimental results, ultra-high-strength mortar can be developed by including 1.5% of GNPs and 20% of SF, in which the CS jumped from 70.7 MPa to 133.3 MPa at the age of 28 days. The FS and TS were 20.66 MPa and 14.67 MPa compared to the control mix (9.75 MPa and 6.36 MPa), respectively. This favorable outcome was credited to the pozzolanic activity of SF and the effectiveness of GNPs in compacting the pores and bridging the cracks at the nanoscale level, which were verified by FE-SEM and EDX. In addition, the developed quadratic equations proved their accuracy in predicting and optimizing the mechanical properties with low error (less than 0.09) and high correlation (R2 > 0.97). It can be concluded that the current work is an important step forward in developing a 3D printing mortar. The lack of reinforcement in the printed mortar structure has been a considerable difficulty, and the SF and GNPs have increased the compressive, flexural, and tensile strengths of the mortar. Thus, these improvements will encourage the industry to utilize sustainable materials to produce more affordable housing.

Properties of Additively Manufactured Geopolymer Incorporating Mineral Wollastonite Microfibers

Improving Mechanical Properties of 3D Printable ‘One-Part’ Geopolymer Concrete with Steel Fiber Reinforcement

Performance Modulation and Optimization of PE Fiber Reinforced 3D-Printed Geopolymer

Modification effect of nanosilica and polypropylene fiber for extrusion-based 3D printing concrete: Printability and mechanical anisotropy

Influence of Waste Glass Powder on Printability and Mechanical Properties of 3D Printing Geopolymer Concrete

Effect of Polypropylene Fibre Addition on Properties of Geopolymers Made by 3D Printing for Digital Construction

The Influence of the Material Structure on the Mechanical Properties of Geopolymer Composites Reinforced with Short Fibers Obtained with Additive Technologies

Study on the Reinforced Properties of Geopolymer Fibers with a Sustainable Development Role

Mechanical properties, durability and environmental assessment of low-carbon cementitious composite with natural fibrous wollastonite

Properties of Fiber-Reinforced Geopolymer Mortar Using Coal Gangue and Aeolian Sand

Development of a Novel Extrusion Device to Improve the Printability of 3D Printable Geopolymer Concrete

Mechanical Properties and Microstructure of Highly Flowable Geopolymer Composites with Low-Content Polyvinyl Alcohol Fiber

Mitigating autogenic shrinkage in high‐performance concrete using wollastonite: A structural enhancement approach

Development of Ultra-High-Performance Silica Fume-Based Mortar Incorporating Graphene Nanoplatelets for 3-Dimensional Concrete Printing Application

Effects of additives on the mechanical properties, rheology, and printing properties of Pcc-based 3DPMs

Improvements in the Printability of Printed Mortar Using In-Situ Polymerization

A new strategy to enhance 3D printability of cement-based materials: In-situ polymerization

Properties of 3D-Printable Ductile Fibre-Reinforced Geopolymer Composite for Digital Construction Applications

WFT-based assessment of the rheological characteristics, particle packing, and buildability of Pcc-FA-GGBFS composite materials for 3D printing

3D Printing of Fiber-Reinforced Calcined Clay-Limestone-Based Cementitious Materials: From Mixture Design to Printability Evaluation

Enhancing Mechanical Properties of 3D Printed Cementitious Composites Utilizing Hybrid Recycled PP and PET Fibers