Abstract:For microelectronic industry, Cu-based substrate and epoxy molding compound (EMC) interface is inherently weak and most likely to delaminate, well-known as a major threat for integrated circuits (ICs) reliability. In this paper, hierarchical whisker-like oxide/Cu cone structure was for the first time to be fabricated by combining electroless plating with heat treatment methods to enhance the interface adhesion between Cu-based substrate and EMC. The surface morphology was characterized by scanning electron microscope (SEM). Result shows that the hierarchical whisker-like oxide/Cu cone film is fine, dense and uniform; Single Cu cone structure is about 3-5 μm in height and 1 μm in root diameter; a layer of whisker-like oxide grows perpendicularly to circular surface of Cu cone, with length ranging from tens to hundreds of nanometers. Adhesion strength between the as-prepared substrates and EMC were measured by button shear test. With consideration of oxidation caused by practical processes (e.g. wire bonding), the interface of EMC and porous oxide formed at 260°C for 5 min was taken as standard sample, representative of practical interface. To further study the effect of whisker-like oxide and Cu cone solely on adhesion performance, whisker-like oxide, porous oxide/Cu cone were investigated as well. Button shear test results reveal that interfacial adhesion strength of EMC and whisker-like oxide, porous oxide/Cu cone, hierarchical whisker-like oxide/Cu cone are 85%, 110% and 162% higher than that of standard interface. Moreover, the mechanism for adhesion improvement was discussed by facture surface observation, failure path assumption and force-displacement curve analysis. Results show that interface of EMC and hierarchical whisker-like oxide/Cu cone exhibits brittle/ductile property with about 3-5 μm thick EMC left on the fracture surface, indicating cohesive failure caused by remarkable mechanical interlocking effect. © 2011 Elsevier Ltd. All rights reserved.

Study of Adhesion for Cu/Ru(Zn) on Dielectrics by an Improved Four-Point Bending Measurement

Study on interface behavior of Be/CuCrZr alloy by diffusion bonding

Adhesion improvement of Cu-based substrate and epoxy molding compound interface by hierarchical structure preparation

Investigation of RuZn Alloy As Barrier to Cu Interconnect

Research on Be/CuCrZr Bonding by Hot Isostatic Pressing at Intermediate Temperature

Assessment of Adhesion of Electroplated Cu and Multilayered Cu Coatings by A Bidirectional Bend Test

Density Functional Theory Study of Cu Adhesion on Rh, Ir, Pd, Ta, Mo, Ru, Co, and Os Surfaces

Ruthenium Barrier/Seed Layer for Cu/Low-κ Metallization

In situ nanomechanical measurement of Cu nanowires

Performance Improved by Incorporating of Ru Atoms into Zr-Si Diffusion Barrier for Cu Metallization

Adhesion study of low-k/Si system using 4-point bending and nanoscratch test

A Study on Adhesive Strength of the Amorphous Electroless Nickel Deposite

Cu Adhesion on Tantalum and Ruthenium Surface: Density Functional Theory Study

Measurement of elastic modulus of films by three-point bend test

Adhesion And Electronic Structures Of Cu/Zn2sno4 Interfaces: A First-Principles Study

Enhancing Wettability of Cu3P/Cu Systems through Doping with Si, Sn, and Zr Elements: Insights from First Principles Analysis

Functionalizing Self-Assembled Monolayers to Reduce Interface Scattering in Ruthenium/dielectric for Next-Generation Microelectronic Interconnects

Nano-mechanical properties measurement of dissimilar bonding 304L/zircalloy-4 by nanoindentation test

Adhesion, bonding and electronic properties of Ti/Zr doped c-BN(100)/Cu(100) interfaces: A first-principles study

Quantitative investigation of the adhesion failure of Ti-based metal thin films on Si wafers

Electrochemically driven rapid wetting of 3YSZ by 60Cu–40Ag and its robust joining to 304 stainless steel