Compact Solid-state Coherent LiDAR Based on In-fiber Beam Scanner

Zhi Li,Bonan Liu,Zihan Zang,Yaqi Han,Lican Wu,Changrui Liao,H. Y. Fu

DOI: https://doi.org/10.1364/acpc.2021.t4d.2

2021-01-01

Abstract:We employ a single-mode fiber to achieve non-mechanical beam-steering in LiDAR system at the first time by adopting a wavelength-swept laser source, which is promising to reduce the cost and the size of LiDAR system.

What problem does this paper attempt to address?

A Fully Solid-State Beam Scanner for FMCW LiDAR Application

Zhaoyang Zhang,Bei Chen,Qiang Zhang,Zhiyan Zhou,Qikai Huang,Xufeng Du,Tingge Dai,Hui Yu,Yuehai Wang,Jianyi Yang

DOI: https://doi.org/10.1109/lpt.2023.3246116

IF: 2.6

2023-01-01

IEEE Photonics Technology Letters

Abstract:We demonstrate a fully solid-state beam scanner that incorporates a Si3N4 photonic integrated switch array, a collimator lens, and a lithographically patterned diffraction grating. The off-chip components enable nearly circular output beams under the reduced system complexity. By manipulating the optical switch array and tuning the input wavelength, two-dimensional beam steering with $32\times23$ = 736 resolvable spots across a $14.3^{\circ }\times 9.9^{\circ }$ field of view (FOV) is realized. Furthermore, the coherent ranging within 18 m is demonstrated experimentally by utilizing the triangular frequency modulation. The tested results validate the feasibility of the proposed beam scanner, which might offer a flexible, scalable, and easily-implemented solution for the solid-state frequency modulated continuous-wave (FMCW) LiDAR.
Solid-state FMCW LiDAR with in-fiber beam scanner

Zhi Li,Bonan Liu,Chang Rui Liao,H. Y. Fu

DOI: https://doi.org/10.1364/OL.440940

IF: 3.6

2022-01-01

Optics Letters

Abstract:The beam scanner is a predominant part in the light detection and ranging (LiDAR) system to achieve three-dimensional (3D) imaging. The solid-state beam-steering device has emerged as a promising candidate technology for a beam scanner with the advantages of robustness, stability, and high scanning speed. Here we propose a frequency modulated continuous wave (FMCW) LiDAR system with an in-fiber solid-state beam scanner. A 45 degrees tilted fiber grating (TFG) is first employed to achieve in-fiber solid-state spectral scanning in the LiDAR system. A maximum output efficiency of 93.7% is achieved with proper polarization control. A single-mode fiber is then used to fabricate a 2-cm 45 degrees TFG, which significantly reduces the size and the cost of the beam scanner in the LiDAR system. We experimentally realize 3D imaging of targets placed at a distance of 1.2 m based on our proposed LiDAR system. In addition, the system can achieve a detection distance of 6 m with a ranging precision of 24 mm. (C) 2022 Optical Society of America
A Hybrid Solid-State Beam Scanner for LiDAR Applications

Zhaoyang Zhang,Qikai Huang,Tingge Dai,Bei Chen,Qiang Zhang,Hui Yu,Yuehai Wang,Jianyi Yang

DOI: https://doi.org/10.1117/12.2642858

2023-01-01

Abstract:We demonstrate a hybrid solid-state beam scanner based on 32-channel silicon nitride optical switch with the assistance of transmission blazed grating. The optical switch exhibits rather low power consumption of 7.2 mW/π. Besides, end-fire antennas offer high optical efficiency with less reflection. Non-mechanical two-dimensional beam steering with range of 14.32° × 9.94° and beam divergence of <0.1° is achieved by wavelength tuning and onchip optical path switching. The proposed system eliminates complex control and time-consuming array phase calibration, providing a flexible, scalable and effective solution for all solid-state coaxial light detection and ranging (LiDAR) technology.
A Hybrid Solid-State Beam Scanner for FMCW LiDAR Application.

Zhaoyang Zhang,Xufeng Du,Zhiyan Zhou,Qikai Huang,Qiang Zhang,Tingge Dai,Hui Yu,Yuehai Wang,Jianyi Yang

DOI: https://doi.org/10.1364/ofc.2023.m3f.1

2023-01-01

Abstract:We demonstrate a hybrid solid-state beam scanner based on a Si 3 N 4 switching array. Two-dimensional beam steering with a 14.3°×9.9° field of view and FMCW ranging operation at a distance of 7.4 m are achieved.
Solid-state FMCW LiDAR with Two-Dimensional Spectral Scanning Using a Virtually Imaged Phased Array.

Zhi Li,Zihan Zang,Yaqi Han,Lican Wu,H. Y. Fu

DOI: https://doi.org/10.1364/oe.418003

IF: 3.8

2021-01-01

Optics Express

Abstract:The beam-steering device is a critical component in LiDAR systems for 3D imaging. Solid-state beam-steering devices attract the most attention for their advantages of robustness, fast beam-steering speed, and stability. However, solid-state beam-steering devices, such as optical phased arrays (OPAs), are challenging to realize 2D scanning ability. Here we employed a virtually imaged phased array (VIPA) in the LiDAR system to realize all solid-state two-dimensional (2D) beam-steering based on dispersion only. A frequency swept laser source is used for performing optical frequency-modulated continuous-wave (FMCW) ranging and 2D beam steering simultaneously. The 2D disperser is compact and can be easily implemented owing to its simple structure. The mechanism of continuous scanning and ranging is beneficial for obtaining high lateral resolution, and a lateral resolution of 0.06° is achieved. 3D maps of the object at a distance of 2 m are obtained with cm-level ranging precision. The frame rate of the proposed LiDAR system only depends on the wavelength-tuning speed of the swept laser source, with the potential to realize ultrafast solid-state LiDAR systems.
High-Speed Two-Dimensional Spectral-Scanning Coherent LiDAR System Based on Tunable VCSEL

Yaqi Han,Zhi Li,Lican Wu,Songping Mai,Xinpeng Xing,H. Y. Fu

DOI: https://doi.org/10.1109/jlt.2022.3217088

IF: 4.7

2022-01-01

Journal of Lightwave Technology

Abstract:Non-mechanical LiDAR systems have attracted extensive research interests due to their advantages of robustness and high beam-steering speed. Recently, spectral scanning has emerged as a promising solid-state beam-steering method, which combines dispersive elements with frequency-swept laser sources to perform ultrafast beam-steering. However, swept light sources used in LiDAR systems, such as semiconductor lasers and supercontinuum sources, are usually suffering from low sweep rate, bulky and high-cost that severely hinder the development of spectral-scanning LiDAR. Here, we propose a non-mechanical spectral-scanning frequency-modulated continuous-wave (FMCW) LiDAR system based on a simple compact tunable vertical-cavity surface-emitting laser (VCSEL). The fast-swept VCSEL together with wavelength division multiplexing (WDM) technology is employed for high-speed beam-steering. Millimeter-level ranging accuracy and a lateral resolution of 0.286° with an overall depth voxel acquisition rate of 128 kHz are achieved experimentally.
Beam-Steering Based on Dispersive Optical Phased Array for FMCW LiDAR Application

Xingyi Jiang,Zhaoyang Zhang,Qikai Huang,Qiang Zhang,Jianyi Yang,Hui Yu

DOI: https://doi.org/10.1364/ofc.2024.th2a.31

2024-01-01

Abstract:We demonstrate dispersive optical phased arrays based on the Si3N4-on-Si platform. Two-dimensional beam steering across a 45.6 °× 10 °FOV with a beam width of 1.45 °× 0.032 °is achieved by wavelength tuning alone. Besides, FMCW ranging operation at a target distance of 10 m are experimentally performed.
Solid-state FMCW LiDAR Based on a 2D Disperser

Zhi Li,Zihan Zang,Xuanyi Liu,Lican Wu,H. Y. Fu

DOI: https://doi.org/10.1364/cleo_at.2021.aw3s.7

2021-01-01

Abstract:By employing a tunable laser and a 2D disperser, we experimentally realize a frequency-modulated continuous-wave lidar system that performs ranging and 2-dimensional non-mechanical beam-steering simultaneously. Reconfigurable high imaging resolution and precise ranging are achieved.
Optical System for Scanning Angle Amplification in Tunable Laser Based All-Solid Lidar

Kai Chang,Qi Chen,Junqiang Zhu,Yayun Li,Xiao Ma,Jianjun Meng,Jiasheng Zhao,Jian-jun He

DOI: https://doi.org/10.1117/12.2654778

2022-01-01

Abstract:An optical system for scanning angle amplification in tunable laser based all-solid lidar is theoretically analyzed and experimentally demonstrated with θ=51° when tuning the wavelength from 1531.2nm to 1566.6nm. We have achieved 22 points beam-steering which is identical to the tunable laser channels. The device has several microseconds beam switching speed and 1.4° beam divergence. The size of the device is compact which is only 5cm×4.5cm×1.8cm, and the total system is low-cost.
Solid-state Lidar with wide steering angle using counter-propagating beams

Yuxuan He,Qiang Wang,Xu Han,Zhonghan Wang,Wenpu Geng,Yuxi Fang,Zhongqi Pan,Yang Yue

DOI: https://doi.org/10.1038/s41598-023-34199-4

IF: 4.6

2023-09-25

Scientific Reports

Abstract:In a solid-state photonics-based Lidar, all essential components can be integrated into a silicon chip. It is simple and effective to use a tunable laser source to implement Lidar's beam steering. However, how to effectively increase the steering angle in a small wavelength tuning range is usually a key challenge due to the limited material and waveguide dispersion. In Silicon-on-insulator waveguide, we design a novel solid-state Lidar using two trans-electrical (TE) polarized beams counter-propagating towards each other. Two corresponding output beams from just a single grating coupler (GC) can be seamlessly combined to double the beam steering angle. Furthermore, a low-priced solid-state Lidar is designed for TE polarized beams counter-propagating towards each other by using wavelength division multiplexed laser array.

multidisciplinary sciences
Spectrally Scanning LiDAR Based on Wide-Angle Agile Diffractive Beam Steering

Zihan Zang,Yunpeng Xu,Haoqiang Wang,Zhi Li,Yanjun Han,Hongtao Li,H. Y. Fu,Yi Luo

DOI: https://doi.org/10.1109/lpt.2022.3190072

IF: 2.6

2022-01-01

IEEE Photonics Technology Letters

Abstract:Spectral scan, or beam steering by only wavelength tuning enables inertia-less fast-scanning LiDAR, while the field of view is fundamentally limited by the total available wavelength range and the dispersion ability of common gratings. Here, we propose to relieve the restriction by combining a diffraction grating and a low-cost diffractive element, which enables wide-angle two-dimensional beam steering. An FoV far beyond the reach of other spectral scan methods can be achieved. Several diffractive elements samples are fabricated to demonstrate spectrally scanning field of views of $7.7^{\circ } \times 10^{\circ }$ and $7.7^{\circ } \times 29^{\circ }$ from an 100-nm wavelength tuning range. Also, to show the potential to further extend the spectral scan range, blazed diffractive elements are fabricated with high diffraction efficiency, which corresponds to a spectral scan range up to 40.3°. Based on the structure, a solid-state coherent LiDAR system is built. Three-dimensional imaging with mm-level range resolution is demonstrated.
Laser Feedback Frequency-Modulated Continuous-Wave LiDAR and 3-D Imaging.

Yifan Wang,Ziyu Hua,Jiachen Shi,Zongren Dai,Jiagang Wang,Liyang Shao,Yidong Tan

DOI: https://doi.org/10.1109/tim.2023.3249246

IF: 5.6

2023-01-01

IEEE Transactions on Instrumentation and Measurement

Abstract:We propose and demonstrate a novel light detection and ranging (LiDAR) system for 3-D imaging, combined with laser feedback interferometry (LFI) and frequency-modulated continuous-wave (FMCW). Compared with the conventional FMCW method, the intracavity interference between the echo signal and local oscillator enhances the amplitude of the generated beat signal effectively, which improves the sensitivity in weak-signal detection with low photon consumption. The improvement is still effective even with frequency modulation nonlinearity. Besides, the system inherits the advantages of FMCW, possessing the capacity to measure position and velocity simultaneously. In experiments, the validity of distance and velocity measurement is demonstrated, and 3-D imaging is realized by employing a pair of beam scanners. With a less than $200 \mu \text{W}$ probe beam, the system achieves imaging over 65 m away in various scenes with good fidelity, and the distance resolution is better than 1 mm. A portable prototype is also designed and fabricated. Overall, the proposed system possesses high echo-signal sensitivity, simple structure, and dynamic information availability, which provides a new idea for FMCW-LiDAR optimization for practical applications.
Highly Compact All-Solid-State Beam Steering Module Based on a Metafiber

Nan He,Xinan Xu,Tingbiao Guo,Rui Chen,Yuxin Xing,Yi Jin,Sailing He

DOI: https://doi.org/10.1021/acsphotonics.2c00848

IF: 7

2022-08-19

ACS Photonics

Abstract:Optical phased arrays occupy the predominant position in the solid-state light detection and ranging; however, their applications are limited by high insertion loss, complex control, and the need for tunable lasers. Here, by assembling a quadratic silicon metalens onto the end face of a single-mode fiber array to form a metafiber, we propose an all-solid-state beam steering module. With the introduction of the flat metalens, the module is highly compact, and the field of view may be extremely wide. A large field of view up to about 60° is testified experimentally based on a one-dimensional module. The application for parking space monitoring is also demonstrated based on a two-dimensional module. The beam steering module can be switched between the scanning mode and the flash mode compatibly and can also be extended to a larger scale with a higher scanning precision by increasing the size of the fiber array and scaling the metalens. The presented scheme featured with high compactness, high performance, and good compatibility provides a distinctive beam steering candidate for light detection and ranging or optical wireless communication applications.

physics, condensed matter,optics, applied,materials science, multidisciplinary,nanoscience & nanotechnology
High SNR signal processing system for coherent solid-state LIDAR with silicon photonic balanced photodetector array

Jing Cao,Xiaoyan Hu,Lijun Yang,Bin Li

DOI: https://doi.org/10.1117/12.2625093

2022-03-27

Abstract:We present a high SNR signal processing system for coherent solid-state LIDAR. A receiving frequency processing system is initially developed. In this LIDAR system, a frequency-modulated continuous wave (FMCW) laser is used as the transmitter, and balanced detectors array based on silicon photonic technology is used as the laser echo receiver. The receiving processing system includes multi-channel low-noise transimpedance amplifier, band-pass filter, high resolution ADC and output buffers. Based on the signal processing system, frequency signal processing with a high signal-to-noise ratio is realized, and the distance detection is realized to confirm on-chip balanced-photodetector-based coherent ranging. The system can be integrated by CMOS technology in the future and realizing three-dimensional integration through through-silicon-via (TSV) with the silicon photonic chip to get low integration complexity, low power consumption, low optical loss, and large array integration.
Solid-State Dtof LiDAR System Using an Eight-Channel Addressable, 20w/ch Transmitter, and a 128x128 SPAD Receiver with SNR-Based Pixel Binning and Resolution Upscaling.

Shenglong Zhuo,Lei Zhao,Tao Xia,Lei Wang,Shi,Yifan Wu,Chang Liu,Chill Wang,Yuwei Wang,Yuan Li,Hengwei Yu,Jiqing Xu,Aaron Wang,Zhihong Lin,Yun Chen,Rui Bai,Xuefeng Chen,Patrick Yin Chiang

DOI: https://doi.org/10.1109/cicc53496.2022.9772823

2022-01-01

Abstract:The ability to capture the spatial dimensions of the world around us is growing in importance, with the widespread adoption of 3D-sensing used today for secure facial authentication, AR occlusion, robotic vision and SLAM, autonomous driving, and 3D-reconstruction. Most state-of-the-art light detection and ranging (LiDAR) systems mainly focus on the sensor design [1]–[4]. However, the optical-electrical system of LiDAR is complex, requiring hardware and software co-optimization across the entire signal chain: high-power sub-1ns pulsed laser drivers, high-efficiency lasers, class-1 laser eye-safety, optical lens for focusing or diffusion, high-SNR single-photon detection receiver arrays, and machine learning (ML) based computational photography.
A Low-Cost High-Resolution Solid-State Lidar With Wavelength Division Multiplexed Components and Interleaved Orthogonal Polarization Grating Couplers

Zhonghan Wang,Qiang Wang,Xu Han,Yuxi Fang,Yuxuan He,Wenpu Geng,Zhongqi Pan,Yang Yue

DOI: https://doi.org/10.1109/jlt.2021.3133462

IF: 4.7

2022-04-01

Journal of Lightwave Technology

Abstract:Laser diodearray and photo diode array combined through coarse wavelength division multiplexed (CWDM) are widely used in short-reach optical communication within massive web-scale data center. Those components can be used in solid-state photonics-based Lidar built upon silicon-on-insulator (SOI) waveguide as well, achieving significant cost saving. Beam steering can be naturally achieved through diffraction in output grating couplers. However, current design is hampered by low angular resolution. We demonstrate a novel design by combining outputs of two grating couplers with orthogonal polarizations in an interleaving manner. This scheme effectively doubles the angular resolution of on-chip Lidar.

engineering, electrical & electronic,optics,telecommunications
Compact And Lightweight 1.5 Mu M Lidar With A Multi-Mode Fiber Coupling Free-Running Ingaas/Inp Single-Photon Detector

Chao Yu,Jiawei Qiu,Haiyun Xia,Xiankang Dou,Jun Zhang,Jian-Wei Pan

DOI: https://doi.org/10.1063/1.5047472

IF: 1.6

2018-01-01

Review of Scientific Instruments

Abstract:We present a compact and lightweight 1.5 mu m lidar using a free-running single-photon detector (SPD) based on a multi-mode fiber (MMF) coupling InGaAs/InP negative feedback avalanche diode. The ultimate light detection sensitivity of SPD highly reduces the power requirement of the laser, whilst the enhanced collection efficiency due to MMF coupling significantly reduces the volume and weight of telescopes. We develop a specific algorithm for the corrections of errors caused by the SPD and erbium-doped fiber amplifier to extract accurate backscattering signals. We also perform a comparison between single-mode fiber (SMF) coupling and MMF coupling in the lidar receiver, and the results show that the collection efficiency with MMF coupling is five times higher than that with SMF coupling. In order to validate the functionality, we use the lidar system for the application of cloud detection. The lidar system exhibits the ability to detect both the cloud base height and the thickness of multi-layer clouds to an altitude of 12 km with a temporal resolution of 1 s and a spatial resolution of 15 m. Due to the advantages of compactness and lightweight, our lidar system can be installed on unmanned aerial vehicles for wide applications in practice. Published by AIP Publishing.
Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering

Bingzhao Li,Qixuan Lin,Mo Li

DOI: https://doi.org/10.1038/s41586-023-06201-6

2023-06-30

Guangxue Jishu/Optical Technique

Abstract:Thanks to its superior imaging resolution and range, light detection and ranging (LiDAR) is fast becoming an indispensable optical perception technology for intelligent automation systems including autonomous vehicles and robotics1–3. The development of next-generation LiDAR systems critically needs a non-mechanical beam-steering system that scans the laser beam in space. Various beam-steering technologies4 have been developed, including optical phased array5–8, spatial light modulation9–11, focal plane switch array12,13, dispersive frequency comb14,15 and spectro-temporal modulation16. However, many of these systems continue to be bulky, fragile and expensive. Here we report an on-chip, acousto-optic beam-steering technique that uses only a single gigahertz acoustic transducer to steer light beams into free space. Exploiting the physics of Brillouin scattering17,18, in which beams steered at different angles are labelled with unique frequency shifts, this technique uses a single coherent receiver to resolve the angular position of an object in the frequency domain, and enables frequency–angular resolving LiDAR. We demonstrate a simple device construction, control system for beam steering and frequency domain detection scheme. The system achieves frequency-modulated continuous-wave ranging with an 18° field of view, 0.12° angular resolution and a ranging distance up to 115 m. The demonstration can be scaled up to an array realizing miniature, low-cost frequency–angular resolving LiDAR imaging systems with a wide two-dimensional field of view. This development represents a step towards the widespread use of LiDAR in automation, navigation and robotics. Three-dimensional imaging using a frequency–angular resolving and frequency-modulated continuous-wave LiDAR enabled by a chip-scale acousto-optic beam-steering device has been demonstrated, with the simplicity and low cost of the device making this a promising technology.
Compact and lightweight 1.5 μ m lidar with a multi-mode fiber coupling free-running InGaAs/InP single-photon detector

Chao Yu,Jiawei Qiu,Haiyun Xia,Xiankang Dou,Jun Zhang,Jian-Wei Pan

DOI: https://doi.org/10.1063/1.5047472

Abstract:We present a compact and lightweight 1.5 μm lidar using a free-running single-photon detector (SPD) based on a multi-mode fiber (MMF) coupling InGaAs/InP negative feedback avalanche diode. The ultimate light detection sensitivity of SPD highly reduces the power requirement of the laser, whilst the enhanced collection efficiency due to MMF coupling significantly reduces the volume and weight of telescopes. We develop a specific algorithm for the corrections of errors caused by the SPD and erbium-doped fiber amplifier to extract accurate backscattering signals. We also perform a comparison between single-mode fiber (SMF) coupling and MMF coupling in the lidar receiver, and the results show that the collection efficiency with MMF coupling is five times higher than that with SMF coupling. In order to validate the functionality, we use the lidar system for the application of cloud detection. The lidar system exhibits the ability to detect both the cloud base height and the thickness of multi-layer clouds to an altitude of 12 km with a temporal resolution of 1 s and a spatial resolution of 15 m. Due to the advantages of compactness and lightweight, our lidar system can be installed on unmanned aerial vehicles for wide applications in practice.
Compact and lightweight 1.5 μm lidar with a multi-mode fiber coupling free-running InGaAs/InP single-photon detector

Chao Yu,Jiawei Qiu,Haiyun Xia,Xiankang Dou,Jun Zhang,Jian-Wei Pan

DOI: https://doi.org/10.1063/1.5047472

2018-10-11

Abstract:We present a compact and lightweight 1.5 {\mu}m lidar using a free-running single-photon detector (SPD) based on a multi-mode fiber (MMF) coupling InGaAs/InP negative feedback avalanche diode. The ultimate light detection sensitivity of SPD highly reduces the power requirement of laser, whilst the enhanced collection efficiency due to MMF coupling significantly reduces the volume and weight of telescopes. We develop a specific algorithm for the corrections of errors caused by the SPD and erbium-doped fiber amplifier to extract accurate backscattering signals. We also perform a comparison between single-mode fiber (SMF) coupling and MMF coupling in the lidar receiver, and the results show that the collection efficiency with MMF coupling is five times higher than SMF coupling. In order to validate the functionality, we use the lidar system for the application of cloud detection. The lidar system exhibits the ability to detect both the cloud base height and the thickness of multi-layer clouds to an altitude of 12 km with a temporal resolution of 1 s and a spatial resolution of 15 m. Due to the advantages of compactness and lightweight, our lidar system can be installed on unmanned aerial vehicles for wide applications in practice.

Applied Physics,Instrumentation and Detectors,Quantum Physics

Compact Solid-state Coherent LiDAR Based on In-fiber Beam Scanner

A Fully Solid-State Beam Scanner for FMCW LiDAR Application

Solid-state FMCW LiDAR with in-fiber beam scanner

A Hybrid Solid-State Beam Scanner for LiDAR Applications

A Hybrid Solid-State Beam Scanner for FMCW LiDAR Application.

Solid-state FMCW LiDAR with Two-Dimensional Spectral Scanning Using a Virtually Imaged Phased Array.

High-Speed Two-Dimensional Spectral-Scanning Coherent LiDAR System Based on Tunable VCSEL

Beam-Steering Based on Dispersive Optical Phased Array for FMCW LiDAR Application

Solid-state FMCW LiDAR Based on a 2D Disperser

Optical System for Scanning Angle Amplification in Tunable Laser Based All-Solid Lidar

Solid-state Lidar with wide steering angle using counter-propagating beams

Spectrally Scanning LiDAR Based on Wide-Angle Agile Diffractive Beam Steering

Laser Feedback Frequency-Modulated Continuous-Wave LiDAR and 3-D Imaging.

Highly Compact All-Solid-State Beam Steering Module Based on a Metafiber

High SNR signal processing system for coherent solid-state LIDAR with silicon photonic balanced photodetector array

Solid-State Dtof LiDAR System Using an Eight-Channel Addressable, 20w/ch Transmitter, and a 128x128 SPAD Receiver with SNR-Based Pixel Binning and Resolution Upscaling.

A Low-Cost High-Resolution Solid-State Lidar With Wavelength Division Multiplexed Components and Interleaved Orthogonal Polarization Grating Couplers

Compact And Lightweight 1.5 Mu M Lidar With A Multi-Mode Fiber Coupling Free-Running Ingaas/Inp Single-Photon Detector

Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering

Compact and lightweight 1.5 μ m lidar with a multi-mode fiber coupling free-running InGaAs/InP single-photon detector

Compact and lightweight 1.5 μm lidar with a multi-mode fiber coupling free-running InGaAs/InP single-photon detector