Multimode Interferometer Based on a Core-Offset Singlemode-Multimode-singlemode Fiber Structure

Xianfan Wang,Caini Zhang,Tengchao Huang,Xiaowu Shu

DOI: https://doi.org/10.1364/psc.2020.jtu3f.11

2020-01-01

Abstract:We propose an all-fiber multimode interferometer based on a core-offset SMS fiber structure, and demonstrate that the lateral core-offset value has a big impact on multimode interference and re-imaging phenomenon within it.

What problem does this paper attempt to address?

Investigation of the self‐imaging position of a singlemode‐multimode‐singlemode optical fiber structure

Xianfan Wang,Elfed Lewis,Pengfei Wang

DOI: https://doi.org/10.1002/mop.30605

IF: 1.311

2017-01-01

Microwave and Optical Technology Letters

Abstract:In this paper, a theoretical and experimental investigation of the multimode interference induced self-imaging phenomenon in a singlemode-multimode-singlemode (SMS) fiber structure is described. The simulated transmission spectra based on guided modal propagation analysis and beam propagation method are presented and compared with experimental obtained results. The temperature dependence of the self-imaging position of the SMS fiber structure is also investigated. These investigations provide excellent opportunities for multiple future applications including telecommunications and sensing.
High-contrast and High-Stable Wavefront Shaping Multimode Fiber Imaging

Qing Yang,Zhong Wen,Chenlei Pang,Mingwei Tang,Xiaowei Liu

DOI: https://doi.org/10.1117/12.2575350

2020-01-01

Abstract:The main challenge in multimode fiber imaging is modal scrambling caused by environmental fluctuation. How to get high contrast and high stable imaging is the main question. In this presentation, we propose some methods to increase the contrast-to-noise ratio and stability of multimode fiber imaging. Wavelength modulation is introduced to suppress the background. Exhaustive bending effect was used to improve the imaging stability. Wavelength modulation is introduced to enhance the CNR four fold in a 200 μm field-of-view imaging. We show a near diffraction limited focusing capability at imaging depths of up to 150 µm with near constant lateral resolutions of 2.1 µm. The imaging of small fluorescent beads embedded in a 3D matrix was demonstrated.
Investigation of a novel SMS fiber based planar multimode waveguide and its sensing performance.

Xianfan Wang,Jiquan Zhang,Ke Tian,Shunbin Wang,Libo Yuan,Elfed Lewis,Gerald Farrell,Pengfei Wang

DOI: https://doi.org/10.1364/OE.26.026534

IF: 3.8

2018-01-01

Optics Express

Abstract:A novel, MMI-based all-fiber structure, which consists of two single-mode fibers and a multimode fiber polished on both sides, is described. The light propagation characteristics of this fiber structure, as well as its superior sensing performance, are analyzed theoretically by using the beam propagation method (BPM). This fiber structure demonstrates a significant spectral response to changes of the surrounding refractive index (RI), and the measured results exhibit good agreement with the predicted data. The measured average RI sensitivity is as high as 151.29 nm/RIU over an RI range from 1.3450 to 1.4050, when the polished depth is 30 mu m on both sides of the multimode fiber. This fiber structure can be an advantageous platform for various applications, especially for a lab-on-fiber type sensing application. (C) 2018 Optical Society of America under the terms of the OSA Open Access Publishing Agreement
A Single-Mode Fiber Sensor Based on Core-Offset Inter-Modal Interferometer

Jingli Fan,Jiangshan Zhang,Ping Lu,Ming Tian,Jun Xu,Deming Liu

DOI: https://doi.org/10.1016/j.optcom.2013.12.055

IF: 2.4

2014-01-01

Optics Communications

Abstract:A single-mode fiber (SMF) sensor based on core-offset inter-modal interferometer is demonstrated. Compared with the sensing head with the two core-offset joints, the improved sensor has a special advantage that the offset direction cannot significantly affect the extinction ratio (ER) of the transmission spectrum. So the improved sensor, which is made of SMF and a very short section of multimode fiber (MMF), appears repeatable and higher extinction ratio. And the refractive index (RI) sensitivity of −64.889nm/RIU and temperature sensitivity of 73pm/°C, respectively can be achieved. Its ease of fabrication makes it a low cost alternative to existing sensing applications.
Design and Fabrication of Multimode Interference Coupler with Strong Confinement Structure on Silicon-On-Insulator

YZ Tang,WH Wang,YM Wu,JY Yang,YL Wang

DOI: https://doi.org/10.1117/1.1804545

IF: 1.3

2004-01-01

Optical Engineering

Abstract:A 1x8 multimode interference coupler with a strong confinement structure in the multimode region was proposed and fabricated on silicon-on-insulator material. In the multimode region, the waveguide was etched to the buried silica layer so as to realize the strong confinement and obtain better resolution of the self-imaging effect, while in the input/output ports, the rib waveguides with the large cross-section rib structure were designed to satisfy the single-mode condition, with which the device could be efficiently coupled with single-mode fibers or other waveguide devices. The fabrication process was also specially designed to eliminate the photolithography alignment error. (C) 2004 Society of Photo-Optical Instrumentation Engineers.
Optical Mode Interleaver Based on the Asymmetric Multimode Y Junction

Weiwei Chen,Pengjun Wang,Jianyi Yang

DOI: https://doi.org/10.1109/lpt.2014.2346082

IF: 2.6

2014-01-01

IEEE Photonics Technology Letters

Abstract:An optical mode interleaver (OMIL) based on the asymmetric multimode Y junction is proposed for realizing flexible selection of group of modes in mode-division multiplexing optical network. The odd and even modes of the stem can be sorted by carefully controlling the widths of the narrow and wide arms according to the constraint conditions of the propagation constants. A four-mode OMIL is analyzed as an example using the beam propagation method. The device is able to realize a low excess loss of <0.13 dB, a high mode extinction ratio that exceeded 28.4 dB, and a mode crosstalk lower than -25.5 dB over a common spectral bandwidth of 210 nm.
Spatial-division Multiplexed Brillouin Distributed Sensing Based on a Heterogeneous Multicore Fiber

Zhiyong Zhao,Yunli Dang,Ming Tang,Borui Li,Lin Gan,Songnian Fu,Huifeng Wei,Weijun Tong,Ping Shum,Deming Liu

DOI: https://doi.org/10.1364/ol.42.000171

IF: 3.6

2017-01-01

Optics Letters

Abstract:We have experimentally investigated spatial-division multiplexed (SDM) Brillouin optical time-domain analysis in a heterogeneous multicore fiber whose central core and six outer cores are made from different preforms, showing a similar to 70 MHz Brillouin frequency shift (BFS) difference between them. It reveals that the heterogeneous central core and the outer cores have different temperature sensitivities, but their strain sensitivities are almost the same. By making use of the distinct temperature coefficients of these two kinds of cores, simultaneous and discriminative temperature and strain measurements are achieved. The bending-induced Brillouin gain spectrum (BGS) broadening issue in off-center cores has been clarified, and a solution has been proposed to eliminate the uncertainty caused by a bending-induced BFS shift, by averaging the BFS variations of two symmetrical outer cores. We show a new perspective for discriminative measurement in Brillouin distributed sensors based on SDM solutions. (C) 2016 Optical Society of America
Mode Couplers and Converters Based on Dual-Core Hollow-Core Photonic Bandgap Fiber

Simeng Han,Zhi Wang,Yange Liu,Hongye Li,Hu Liang,Zhenhong Wang

DOI: https://doi.org/10.1109/jphot.2018.2810059

IF: 2.4

2018-01-01

IEEE Photonics Journal

Abstract:We propose mode couplers and converters based on dual-core hollow-core photonic bandgap fiber (HC-PBGF) structures, which might be potential solutions for integrated all-fiber multiplexers or demultiplexers of a mode-division multiplexed (MDM) transmission system using HC-PBGFs. Coupling properties of LP01 and LP11 mode in the mode coupler are investigated and applied to mode separators and polarization separators. Mode transition from LP01 to LP11 and LP21 mode are demonstrated in the mode converter whose smaller core is expected as input end and matched with single-mode fiber. The coupling between fundamental mode and high-order modes is accomplished through the resonant effect, which is fulfilled by modifying the structure parameter of the smaller core. Such mode converters based on dual-core HC-PBGF could be a promising substitute for the free-space coupling device, which is costly and not suitable for integration design in MDM systems and other hollow-core fiber experiments and applications.
High-resolution, large-dynamic-range multimode interferometer sensor based on a suspended-core microstructured optical fiber

Yu Zheng,Perry Ping Shum,Yiyang Luo,Yanan Zhang,Wenjun Ni,Guanghui Wang,Zhifang Wu,Xuan Quyen Dinh,Jean-Louis Auguste,Georges Humbert

DOI: https://doi.org/10.1364/OL.386296

IF: 3.6

2020-01-01

Optics Letters

Abstract:The performance of sensors, including optical fiber sensors, is commonly limited by the tradeoff between a large dynamic range and a high resolution. In this Letter, in order to optimize both, we propose an inline multimode interferometer sensor based on a suspended-core microstructured. optical fiber. Due to the existence of multiple pairs of mode interferences, the transmission spectrum of the interferometer consists of dense fringes modulated by a lower envelope. Since these mode interferences take place in the uniform material with the same length, the dense fringes and the lower envelope have an identical sensing response without crosstalk. Hence, the sensor integrates the large dynamic range of the lower envelope and the high resolution of the dense fringes. Strain-sensing performance is investigated to valid ate the characteristic of the large dynamic range and the high resolution of the proposed sensor. The dynamic range, theoretically 0-9200 mu epsilon, is 12 times larger than for the dense fringes, and the resolution is 17.5 times higher than for the lower envelope. (C) 2020 Optical Society of America
Optimization Analysis of Lateral-Offset Mach–Zehnder Interferometer Based on No-Core Fiber

Duo Yi,Zhenwei Huo,Xiaoling Tan,Youfu Geng,Fei Liu,Xuejin Li

DOI: https://doi.org/10.1109/jsen.2021.3073603

IF: 4.3

2021-07-01

IEEE Sensors Journal

Abstract:In this work, we thoroughly evaluate different types of lateral-offset Mach-Zehnder interferometers (MZIs) to search for the optimized design. Three different structures (SNS, SMNMS, and SNNNS. S: single-mode fiber; N: no-core fiber; M: multi-mode fiber) are proposed and their performances are compared numerically. Besides, for the SNNNS sensor, the effect of different no-core fiber (NCF) diameters on the sensor performance is discussed. The numerical analyses demonstrate that the SNNNS sensor with NCF diameter of $61.5{mu m}$ shows the best performance among all the sensors. The experimental results confirm that, when compared with the SNS sensor, the SNNNS sensor is insensitive to the lateral-offset distance. It ensures an excellent interference performance within a large offset range, which facilitates the sensor fabrication. The optimized design of the sensor device shows the potential integration applications in the ultra-low concentration biomolecule detection field.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
Optical Fiber Sensors Based on Core-Offset Structure: A Review

Huiwen Niu,Shuo Zhang,Wenhuan Chen,Yue Liu,Xiang Li,Yunxiang Yan,Shengjia Wang,Tao Geng,Weimin Sun,Libo Yuan

DOI: https://doi.org/10.1109/jsen.2021.3110852

IF: 4.3

2021-10-15

IEEE Sensors Journal

Abstract:This review focuses on the preparation methods and wide applications of optic fiber sensors based on core-offset structure. Firstly, the classification and preparation methods of core-offset structures are introduced. Then, the applications of different types of sensors based on the core-offset structure are investigated, including the measurement of physical parameters such as temperature, strain, refractive index (RI), bending, magnetic field by Mach-Zehnder interferometer (MZI), cascaded sensor, long period fiber grating (LPFG), fiber Bragg grating (FBG), Fabry-Perot interferometer (FPI) and Surface plasmon resonance (SPR). Compared with the traditional fiber sensor, core-offset structure sensor with a non-axisymmetric characteristic has excellent sensing characteristics, especially in the recognition of bending direction and high RI sensitivity. Furthermore, the design scheme, working principle and sensing characteristics of different core-offset sensors are also briefly described. Finally, the existing challenges and development direction of optic fiber sensors based on core-offset structure is discussed and prospected.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
A Mach–Zehnder Interferometer Based on a No-Core Fiber With In-Fiber Waveguides

Hua Zhang,D. N. Wang,Z. K. Wang,Ben Xu,C. L. Zhao,Shuqin Zhang,Jianqing Li

DOI: https://doi.org/10.1109/lpt.2019.2918293

IF: 2.6

2019-07-01

IEEE Photonics Technology Letters

Abstract:A Mach–Zehnder interferometer constructed by femtosecond-laser written in-fiber waveguides in no-core fiber (NCF) is demonstrated. Such an interferometer device consists of a section of the NCF in which a waveguide has been inscribed, fusion spliced with single-mode fiber at its two ends. One of the interferometer arms is formed by the waveguide inscribed and the other follows the diverging light path inside the NCF before arriving at the end of single-mode fiber core. Such an internal structure-based device can be used not only for strain sensing but also for external refractive index measurement.
Inline fiber interference-based refractive-index sensor

zhenfeng gong,xinpu zhang,yun liu,zigeng liu,qingxu yu,wei peng

DOI: https://doi.org/10.1117/1.OE.53.11.117106

IF: 1.3

2014-01-01

Optical Engineering

Abstract:We report two fiber multiple-mode interferometers formed in photonic crystal fiber (PCF). The interference between the core and the cladding modes of a PCF is utilized. We use two methods to form a coupling point, and the cladding modes are excited from the fundamental core mode. One method is blowing compressed gas into the air holes and discharging at the coupling point; the air holes will expand due to gas expansion in the discharge process. Similarly, the other is discharging at the coupling point after the air is exhausted from the air holes, and the holes will contract during the process. By making another coupling point at a different location along the fiber, the proposed PCF interferometers are implemented. Experimental results show that the sensitivities of the two devices can achieve 1.54 and 1.45 nm for a 0.01 refractive index change. (C) 2014 Society of Photo-Optical Instrumentation Engineers (SPIE)
PDMS-coated fiber optic interferometer based on no-core fiber for multi-parameter measurements

Duo Yi,Zenan Zhang,Youfu Geng,Xuejin Li,Xueming Hong

DOI: https://doi.org/10.1117/12.2548405

2020-01-01

Abstract:This study proposes a novel fiber-optic interferometer based on the single-mode fiber-no core fiber-single mode fiber structure with the coated polydimethylsiloxane (PDMS). The no core fiber is the key carrier to excite the modal interference, and the PDMS that covers onto the fiber cascade structure is able to enhance the sensor sensitivity and also protect the sensor structure. The experimental results verify that the proposed sensor owns a high temperature sensitivity and the strain sensitivity, and it is particularly suitable for multi-parameter measurements.
Micro-displacement sensor based on an asymmetric wavy multimode fiber interferometer

Yuanzheng Li,Yi Li,Yinping Miao,Fang Wang,Kai Hu,Kailiang Zhang

DOI: https://doi.org/10.1007/s11801-023-2139-5

2023-03-28

Optoelectronics Letters

Abstract:We proposed a compact and tunable multimode interferometer (MMI) based on an asymmetric wavy fiber (AMWF), which has axial offset, off-center taper waist, and micro-length. The fabrication process only contains non-axis pulling processes of single-mode fiber on two close positions. Theoretical qualitative analyses and experiments verify the tunable multimode propagation of the AMWF. Experimental results show a nonlinear wavelength response with increasing axis displacement from 0 to 120 μm. In the range of 0–10 μm, the sensitivity reaches the highest value of −1.33 nm/μm. Owing to its cost-effective, high-compact and tunable multimode propagation properties, the AMWF provides a promising platform for micro-nano photonic devices and optical sensing applications.

optics
19-Ring-air-core Fiber Supporting Thousands of OAM Modes for Spatial Division Multiplexing

Yingning Wang,Wenqian Zhao,Jiahe Hu,Zhi Wang,Yan-Ge Liu,Changjing Bao,Yongxiong Ren,Zhongqi Pan,Yang Yue

DOI: https://doi.org/10.1364/ol.453079

IF: 3.6

2022-01-01

Optics Letters

Abstract:We propose and design a 19-ring-air-core fiber that can support about 3000 orbital angular momentum (OAM) modes (156 modes in each ring) with <-80 dB inter-ring cross talk across the entire C and L bands after 100-km fiber propagation. Moreover, the eigenmodes are all separated from their adjacent modes by effective index differences >2.67 × 10-4 and mode groups by > 1.90 × 10-2, which can guarantee the stable transmission of OAM modes. This designed fiber is a potential candidate for applications in spatial division multiplexing (SDM) of optical channels to improve the capacity of next-generation high-speed optical communication systems, especially in short-distance applications. In this Letter, we also show the relationship between supported OAM mode numbers, total cross talk, and effective refractive index of intra-ring modes during the optimization of fiber through numerical simulations. It can provide a related reference for the future design of multi-ring-core fibers.
Multimode Excitation-Induced Phase Shifts in Intrinsic Fabry-Perot Interferometric Fiber Sensor Spectra

Cheng Ma,Anbo Wang

DOI: https://doi.org/10.1364/ao.49.004836

IF: 1.9

2010-01-01

Applied Optics

Abstract:We report the modal analysis of optical fiber single-mode-multimode-single-mode intrinsic Fabry-Perot interferometer sensors. The multimode nature of the Fabry-Perot cavity gives rise to an additional phase term in the spectrogram due to intermodal dispersion-induced wavefront distortion, which could significantly affect the cavity length demodulation accuracy. By using an exact model to analyze the modal behavior, this phase term is explained by employing a rotating vector approach. Comparison of the theoretical analysis with experimental results is presented.
Multimode Fiber-Based Interferometric Sensors With Microwave Photonics

Chen Zhu,Shuaifei Tian,Lingmei Ma,Jie Huang

DOI: https://doi.org/10.1109/jlt.2024.3373122

IF: 4.7

2024-01-01

Journal of Lightwave Technology

Abstract:Interferometry is one of the most widely used investigative techniques in various fields. With the implementation of interferometry on optical fibers, fiber optic interferometers (FOIs) have gained tremendous growth and advancement in the past four decades and have been explored for measurements of a diverse array of physical, chemical, and biological parameters. FOIs are typically constructed using single-mode fibers (SMFs) and are interrogated in the optical domain using probing light with a tightly controlled state of polarization (SOP), to ensure high-quality interference signals that facilitate sensing applications. The stringent requirement on the single-mode operation, as well as SOP, has hindered the further development of FOIs, for example, multimode fiber (MMF)-based FOIs. In this article, we present a comprehensive study of optical fiber-based microwave-photonic interferometers, which are based on a recently developed technique, optical carrier-based microwave interferometry (OCMI). The proposed sensing configuration enabled by the OCMI interrogation, namely, the microwave-photonic interferometer, essentially overcomes the two limiting aspects of traditional FOIs by reading FOIs in the microwave domain. The microwave-photonic interferometers are immune to variations of the SOP of the optical carrier and have low dependence on the types of optical fibers (SMFs and MMFs). We present a complete mathematical model of the microwave-photonic interferometric system. Then, the system is validated using three different types of interferometers, including the Mach-Zehnder interferometer, the Fabry-Perot interferometer, and the Michelson interferometer, based on both SMFs and MMFs. The sensing capability of the proposed system is verified for strain measurements using SMF and a multimode polymer optical fiber. The microwave-photonic interferometric configuration might pave the pathway forward for further expansion of FOIs in various sensing applications.

engineering, electrical & electronic,optics,telecommunications
Design of Solid-Core Bragg Few-Mode Fiber for Short-Reach MDM Networks in O+C+L Band

Yuwei Su,Tianwen Zhangsun,Fang Ren,Yiying Zhang,Jie Yi,Wei Chen,Xiaojie Fan,Jianping Wang

DOI: https://doi.org/10.1016/j.optcom.2020.125245

IF: 2.4

2020-01-01

Optics Communications

Abstract:We propose a solid-core Bragg few-mode fiber with alternating layers of high/low refractive indices. The refractive index of the low-index layer in the cladding is the same as that of the fiber core. The influences of filling ratio, periodic structure width and core size on n(eff), Delta n(eff) and Alpha(eff) are investigated. Bending loss of each guided mode and differential mode delay (DMD) between adjacent spatial modes are also studied at 1550 nm. With appropriate geometrical parameters, the minimum effective refractive index difference (min Delta n(eff)) between adjacent modes is 2x10(-3) at 1550 nm. Wavelength-dependent performance is analyzed subsequently ranging from 1180 nm to 1630 nm. Numerical simulations indicate that such fiber could support 7 linearly polarized (LP) modes and have good bending insensibility performance. These results illustrate that the proposed fiber could be a promising candidate for mode division multiplexing to enhance optical transmission capacity.
Transverse Mode Switchable Fiber Laser with a Multimodal Interference-Based Beam Shaper

Wentan Fang,Xiaohui Ma,Yong Zhou,Wei Zhang,Xiaolin Chen,Song Huang,Meisong Liao,Yasutake Ohishiand,Weiqing Gao

DOI: https://doi.org/10.1364/ol.478033

2022-01-01

Abstract:We propose a Yb-doped fiber laser with an all-fiber beam shaper based on a single-mode-graded-index multimode-few-mode fiber (SMF-GIMF-FMF) structure. The excitation coefficients of the mode can be adjusted continuously by changing the GIMF length. Numerical simulations are performed to investigate the beam shaping dynamics in the fiber structure. Through adding the simple device geometry in the laser cavity, the switchable output between the fundamental transverse (LP01) mode and the second-order transverse (LP11) mode can be achieved. Cylindrical vector beams with high mode purity are also shown by removing the degeneracy of the LP11 mode.

Multimode Interferometer Based on a Core-Offset Singlemode-Multimode-singlemode Fiber Structure

Investigation of the self‐imaging position of a singlemode‐multimode‐singlemode optical fiber structure

High-contrast and High-Stable Wavefront Shaping Multimode Fiber Imaging

Investigation of a novel SMS fiber based planar multimode waveguide and its sensing performance.

A Single-Mode Fiber Sensor Based on Core-Offset Inter-Modal Interferometer

Design and Fabrication of Multimode Interference Coupler with Strong Confinement Structure on Silicon-On-Insulator

Optical Mode Interleaver Based on the Asymmetric Multimode Y Junction

Spatial-division Multiplexed Brillouin Distributed Sensing Based on a Heterogeneous Multicore Fiber

Mode Couplers and Converters Based on Dual-Core Hollow-Core Photonic Bandgap Fiber

High-resolution, large-dynamic-range multimode interferometer sensor based on a suspended-core microstructured optical fiber

Optimization Analysis of Lateral-Offset Mach–Zehnder Interferometer Based on No-Core Fiber

Optical Fiber Sensors Based on Core-Offset Structure: A Review

A Mach–Zehnder Interferometer Based on a No-Core Fiber With In-Fiber Waveguides

Inline fiber interference-based refractive-index sensor

PDMS-coated fiber optic interferometer based on no-core fiber for multi-parameter measurements

Micro-displacement sensor based on an asymmetric wavy multimode fiber interferometer

19-Ring-air-core Fiber Supporting Thousands of OAM Modes for Spatial Division Multiplexing

Multimode Excitation-Induced Phase Shifts in Intrinsic Fabry-Perot Interferometric Fiber Sensor Spectra

Multimode Fiber-Based Interferometric Sensors With Microwave Photonics

Design of Solid-Core Bragg Few-Mode Fiber for Short-Reach MDM Networks in O+C+L Band

Transverse Mode Switchable Fiber Laser with a Multimodal Interference-Based Beam Shaper