Abstract:The unexpected damages are usually introduced during the machining of carbon fibre reinforced composites. There have been experimental investigations on the damage extent for machining thermoset and thermoplastic composites, and numerical simulations developed for the cutting characteristics of thermoset composites. However, studies on the material removal and chip formation mechanisms during the cutting of carbon fibre reinforced thermoplastics (CFRTPs), are rarely reported, which will significantly contribute to the machining quality improvement of CFRTPs. To this issue, numerical simulations and experiments were conducted in this paper to analyse the cutting mechanisms of CFRTPs, and to compare their cutting processes with the carbon/epoxy composites for guidance on damage suppression. In the developed finite element (FE) models, the carbon/epoxy composites were defined to be anisotropic with an elastic constitutive model, while an elastic-plastic damage model was proposed for CFRTPs. Specifically, a plastic yield function consisting of three-dimensional (3D) stress components was utilized to characterise the plasticity of CFRTPs under complex cutting loads. For these two materials, the initiation and evolution of the damage with different failure modes were determined based on the Hashin and Puck criteria and the strain energy density. With these FE models, the orthogonal cutting processes and forces of the composites under four fibre orientations were predicted, and the results agree well with the experimental outputs. It was found that the material removal mechanisms of CFRTPs with the four fibre orientations are diverse from the ones made from thermoset resins in terms of crack propagation, material fracture position and chip formation. Additionally, the shorter cracks and longer chips are usually produced when cutting CFRTPs with 0° and 45° fibre orientations compared with those of the carbon/epoxy composites with same layups. Moreover, the cutting forces of CFRTPs are higher than the carbon/epoxy composites at 0°, 45° and 135° fibre orientations.

Three-dimensional finite element simulations of milling carbon/epoxy composites

2D Macro-Mechanical FE Simulations for Machining Unidirectional FRP Composite: the Influence of Damage Models

Modeling and Analysis of Force Prediction in Milling Process of Unidirectional Fiber Reinforced Polymer Composites

A 3d Progressive Material Damage Model for Fe Simulation of Machining A Unidirectional Frp Composite

Factor Analysis of Machining Parameters of Fiber-Reinforced Polymer Composites Based on Finite Element Simulation with Experimental Investigation

High-speed milling of CFRP composites: a progressive damage model of cutting force

Research on Multiscale Modeling and Experiment of CFRP Milling

Analysis of Burr and Tear in Milling of Carbon Fiber Reinforced Plastic (CFRP) Using Finite Element Method

Research on the Mesoscopic Cutting Mechanism of CFRP Based on Three-dimensional Multiphase Finite Element Models

Numerical Simulation on Mechanical Properties and Damage Behavior of CFRP with Self-Healing Microvascular Channels

Computational simulation of the damage response for machining long fibre reinforced plastic (LFRP) composite parts: A review

A 3D finite element model to simulate progressive damage in unidirectional- and woven-fibre thermoplastic discontinuous-long-fibre composites

Analytical and Numerical Investigation on the Mechanical Behavior of Subsurface Damage During Orthogonal Cutting of Carbon Fiber Reinforced Polymer Composites

Study on Cutting Force Performance and Cutting Mechanism of Carbon Fiber Reinforced Polymer (CFRP) Composites

Micromechanical Modelling of Elliptic Vibration-Assisted Cutting of Unidirectional Frp Composites

Modeling and simulation of milling forces in milling plain woven carbon fiber-reinforced plastics

Microscopic analytical and numerical investigation of orthogonal cutting cfrp

Optimization of Multi-Tooth Milling Tool for Interlaminar Damage Suppression in the Milling of Carbon Fiber–reinforced Polymers

Micro-Mechanical Model And Material Removal Mechanism Of Machining Carbon Fiber Reinforced Polymer Composite

A Comparison of Cutting Mechanisms of the Carbon Fibre Reinforced Thermoset and Thermoplastic Composites by the Experimental and Computational Modelling Methods

Investigation on Cutting Damage Mechanism of Carbon Fiber Reinforced Polymer Based on Macro/microscopic Simulation