Abstract:The CFRP/Ti6Al4V composite has excellent properties of CFRP and Ti6Al4V. Therefore, they are widely used in aerospace and some military fields. The laminated structure of CFRP/Ti6Al4V composite is different from the traditional homogeneous workpiece, and the properties of each layer are diverse, so the processing performance is poor. The experimental research cost of CFRP/Ti6Al4V composites is relatively high and has certain limitations. The finite element method is a promising alternative. In the research, a finite element model combining the macro and micro with the fiber orientation of 90 degrees was established. By combining the mechanism of exit burr formation in the cutting direction of Ti6A14V and the delamination mechanism of CFRP composites, a new mechanical model was proposed for CFRP/Ti6Al4V composites during this study, and it was found that there is not a linear relationship between the rake angle and the delamination of CFRP/Ti6Al4V composites during the cutting process. The results show that the delamination damage of CFRP/Ti6Al4V composites is serious when the rake angle is 4 degrees similar to 10 degrees. The delamination damage is light when the rake angle is 0 degrees similar to 4 degrees. And the delamination damage is the smallest when the rake angle is 10 degrees similar to 20 degrees. In the cutting process, the tremor of the Ti6Al4V phase is also an important factor for delamination. During the extrusion of Ti6Al4V relative to the CFRP phase, the fragmentation of the epoxy matrix leads to brittle fracture of the carbon fibers and shear damage can occur. The brittle fracture height is minimum when the rake angle is 16 degrees. The shear damage height is minimum when the rake angle is 10 degrees. The tremor of Ti6Al4V phase is also an important factor for delamination damage. The fracture of the epoxy resin matrix leads to brittle fracture and shear damage of carbon fiber. The brittle fracture height has a linear relationship with the fracture height of epoxy resin. When the cutting sequence is CFRP -> Ti6Al4V, a better surface quality can be obtained, effectively avoiding carbon fiber brittle fracture. Therefore, the rake angle and cutting sequence are of great importance for processing CFRP/Ti6Al4V composites. Therefore, it is of reference significance for the machining of 90 degrees fiber orientation.

Analysis of Burr and Tear in Milling of Carbon Fiber Reinforced Plastic (CFRP) Using Finite Element Method

Concurrent Multiscale Modeling of In-Plane Micro-Damage Evaluation in Z-pinned Composite Laminates

Modeling of dynamic milling forces considering the interlaminar effect during milling multidirectional CFRP laminate

A Unified Geometrical Modeling and Analysis Method for Evaluating CFRP Machining Performance: Cutting Geometry Space

Factor Analysis of Machining Parameters of Fiber-Reinforced Polymer Composites Based on Finite Element Simulation with Experimental Investigation

A progressive damage model for carbon fiber-reinforced polymer laminates subjected to fastener pull-through failure

Research on Multiscale Modeling and Experiment of CFRP Milling

An analytical approach to cutting force prediction in milling of carbon fiber reinforced polymer laminates

Considering the Bottom Edge Cutting Effect of the Carbon Fiber Reinforced Polymer Milling Force Prediction Model and Optimization of Machining Parameters

Theoretical model of instantaneous milling force for CFRP milling with a ball-end milling cutter: Considering spatial dimension and temporal dimension discontinuity effects

A 3D finite element model to simulate progressive damage in unidirectional- and woven-fibre thermoplastic discontinuous-long-fibre composites

A New Three-Dimensional Progressive Damage Model for Fiber-Reinforced Polymer Laminates and Its Applications to Large Open-Hole Panels

Investigation of CFRP cutting mechanism variation and the induced effects on cutting response and damage distribution

Delamination and Chip Breaking Mechanism of Orthogonal Cutting CFRP/Ti6Al4V Composite

Study on the formation mechanism of cutting surface of carbon fiber-reinforced composites

Finite Element Method of a Progressive Intralaminar and Interlaminar Damage Model for Woven Fibre Laminated Composites under Low Velocity Impact

Cutting Modeling of Hybrid CFRP/Ti Composite with Induced Damage Analysis

Numerical prediction of the chip formation and damage response in CFRP cutting with a novel strain rate based material model

Study on Damage Evaluation and Machinability of UD-CFRP for the Orthogonal Cutting Operation Using Scanning Acoustic Microscopy and the Finite Element Method

Investigations on Micro-Cutting Mechanism and Surface Quality of Carbon Fiber-Reinforced Plastic Composites

Development of a Numerical Material Model for Axial Crushing Mechanical Characterization of Woven CFRP Composites