Abstract:Metal cutting is one of the most frequently used forming processes in the manufacturing industry. Extensive effort is made to improve its process and simulation has become an integrated part, not only in the product development process but also in the customer relations. However, simulation of metal cutting is complex both from numerical as well as physical point of view. Furthermore, modelling the material behaviour has shown to be crucial. Errors in the material model cannot be reduced by the numerical procedures. The magnitudes of strain and strain rate involved in metal cutting may reach values of 1-10 and 103-106 s-1. The dissipative plastic work together with the chip tool friction also leads to locally high temperatures. These extreme ranges of conditions imply that a diversity of physical phenomena is involved and it is a challenge to develop a material model with adequate accuracy over the whole loading range. Furthermore, this intense and severe deformation represents thermo-mechanical behaviour farfrom what is generated from conventional material compression and tension testing. A highly desirable feature is also a material model that can be extrapolated outside the calibration range. This is not trivial since materials exhibit different strain hardening and softening characteristics at different strains, strain rates and temperatures. Models based on modelling some aspects of the underlying physical process, e.g. the generation of dislocations, are expected to have a larger range of validity than engineering models. Though, engineering models are the far most common models used in metal cutting simulations. The scope of this work includes development of validated models for metal cutting simulations of AISI 316L stainless steel. Particular emphasis is placed on the material modeling and high strain rate plasticity phenomena. The focus has been on a physically based material model. The approach has been to review the literature about flow stress models and phenomena and particularly at high strain rates. A previous variant of a dislocation density model has thereafter been extended into high strain rate regimes by applying different mechanisms. Some of the models have been implemented in commercial finite element software for orthogonal cutting simulations. Experimental measurements and evaluations that include SHPB-measurements, cutting force measurements, quick-stop measurements and some microstructural examinations has been conducted for calibration and validation. The compression tests, within a temperature and strain rate range of 20-950 °C and 0.01-9000 s-1 respectively, showed that the flow stress increased much more rapidly within the dynamic loading range and hence depends on the strain rate. The dynamic strain aging (DSA) that has been observed at lower strain rates is non-existent at higher strain rates. The temperature and strain-rate evolution is such that the DSA is not necessary to include when modelling this process. Furthermore the magnetic balance measurements indicate that the martensite transformation-strengthening effect is insignificant within the dynamic loading range. In the present work the concept of motion of dislocations, their resistance to motion and substructure evolution are used as underlying motivation for description of the flow stress. A coupled set of evolution equations for dislocation density and mono vacancy concentration is used rendering a formulation of a rate-dependent yield limit in context of rate-independent plasticity. Dislocation drag due to phonon and electron drag, a strain rate dependent model of the subcell formation, a strain rate and temperature dependent recovery function and a structural dependent thermally activated stress component have among others been considered. Best predictability was obtained with a strain rate dependent subcell formulation. Dislocation drag did not improve the predictability within the measured testing range. Although showed to has a greater influence outside the range of calibration when extrapolated. It has been shown thatextrapolation is uncertain. Results from experiments and modelling of material behaviour and metal cutting together with the literature indicate that the predictability of the material behaviour within and outside the measured testing range can be further tuned by implementing models of the phenomenon mechanical twining and recrystallization.

Numerical prediction of the chip formation and damage response in CFRP cutting with a novel strain rate based material model

Modeling and Analysis of Force Prediction in Milling Process of Unidirectional Fiber Reinforced Polymer Composites

Simulation of Chip Formation in High-Speed Hard Machining

An analytical approach to cutting force prediction in milling of carbon fiber reinforced polymer laminates

A Unified Geometrical Modeling and Analysis Method for Evaluating CFRP Machining Performance: Cutting Geometry Space

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Investigation of CFRP cutting mechanism variation and the induced effects on cutting response and damage distribution

Factor Analysis of Machining Parameters of Fiber-Reinforced Polymer Composites Based on Finite Element Simulation with Experimental Investigation

A cutting force prediction model for rotary ultrasonic side grinding of CFRP composites considering coexistence of brittleness and ductility

Research on CFRP cutting mechanism by the micro-textured tool using macroscopic and microscopic numerical simulations

Investigation on the Effects of Microstructure on Machining Unidirectional Carbon Fiber Reinforced Polymer Composites with a Modified Force Model

Considering the Bottom Edge Cutting Effect of the Carbon Fiber Reinforced Polymer Milling Force Prediction Model and Optimization of Machining Parameters

Numerical model of unidirectional CFRP in machining: Development of an amended friction model

Analysis of Burr and Tear in Milling of Carbon Fiber Reinforced Plastic (CFRP) Using Finite Element Method

Theoretical model of instantaneous milling force for CFRP milling with a ball-end milling cutter: Considering spatial dimension and temporal dimension discontinuity effects

A New Three-Dimensional Progressive Damage Model for Fiber-Reinforced Polymer Laminates and Its Applications to Large Open-Hole Panels

Modelling of high strain rate plasticity and metal cutting

Study on the formation mechanism of cutting surface of carbon fiber-reinforced composites

Numerical and experimental investigation of orthogonal cutting of carbon fiber-reinforced polyetheretherketone (CF/PEEK)

A prediction model of drilling force in CFRP internal chip removal hole drilling based on support vector regression

Quality prediction and process optimization in abrasive waterjet cutting of ultra‐thick carbon fiber reinforced polymer