Abstract:The CFRP/Ti6Al4V composite has excellent properties of CFRP and Ti6Al4V. Therefore, they are widely used in aerospace and some military fields. The laminated structure of CFRP/Ti6Al4V composite is different from the traditional homogeneous workpiece, and the properties of each layer are diverse, so the processing performance is poor. The experimental research cost of CFRP/Ti6Al4V composites is relatively high and has certain limitations. The finite element method is a promising alternative. In the research, a finite element model combining the macro and micro with the fiber orientation of 90 degrees was established. By combining the mechanism of exit burr formation in the cutting direction of Ti6A14V and the delamination mechanism of CFRP composites, a new mechanical model was proposed for CFRP/Ti6Al4V composites during this study, and it was found that there is not a linear relationship between the rake angle and the delamination of CFRP/Ti6Al4V composites during the cutting process. The results show that the delamination damage of CFRP/Ti6Al4V composites is serious when the rake angle is 4 degrees similar to 10 degrees. The delamination damage is light when the rake angle is 0 degrees similar to 4 degrees. And the delamination damage is the smallest when the rake angle is 10 degrees similar to 20 degrees. In the cutting process, the tremor of the Ti6Al4V phase is also an important factor for delamination. During the extrusion of Ti6Al4V relative to the CFRP phase, the fragmentation of the epoxy matrix leads to brittle fracture of the carbon fibers and shear damage can occur. The brittle fracture height is minimum when the rake angle is 16 degrees. The shear damage height is minimum when the rake angle is 10 degrees. The tremor of Ti6Al4V phase is also an important factor for delamination damage. The fracture of the epoxy resin matrix leads to brittle fracture and shear damage of carbon fiber. The brittle fracture height has a linear relationship with the fracture height of epoxy resin. When the cutting sequence is CFRP -> Ti6Al4V, a better surface quality can be obtained, effectively avoiding carbon fiber brittle fracture. Therefore, the rake angle and cutting sequence are of great importance for processing CFRP/Ti6Al4V composites. Therefore, it is of reference significance for the machining of 90 degrees fiber orientation.

Investigation on Cutting Damage Mechanism of Carbon Fiber Reinforced Polymer Based on Macro/microscopic Simulation

FEM Simulation Analysis of Subsurface Damage Formation Based on Continuously Cutting Process of CFRP

Study on the formation mechanism of cutting surface of carbon fiber-reinforced composites

Research on the Carbon Fibre-Reinforced Plastic (CFRP) Cutting Mechanism Using Macroscopic and Microscopic Numerical Simulations

Investigation of CFRP cutting mechanism variation and the induced effects on cutting response and damage distribution

2D Macro-Mechanical FE Simulations for Machining Unidirectional FRP Composite: the Influence of Damage Models

Research on the Mesoscopic Cutting Mechanism of CFRP Based on Three-dimensional Multiphase Finite Element Models

Numerical Analysis of the Effects of Cutting Parameters on the Sub-Surface Damage in Machining of CFRPs

Numerical modeling on the influence of process parameters to the sub-surface damage during the cutting process of carbon fiber reinforced plastic composites

A Unified Geometrical Modeling and Analysis Method for Evaluating CFRP Machining Performance: Cutting Geometry Space

Microscopic analytical and numerical investigation of orthogonal cutting cfrp

Investigation on the Effects of Microstructure on Machining Unidirectional Carbon Fiber Reinforced Polymer Composites with a Modified Force Model

Analytical and Numerical Investigation on the Mechanical Behavior of Subsurface Damage During Orthogonal Cutting of Carbon Fiber Reinforced Polymer Composites

Investigations on Micro-Cutting Mechanism and Surface Quality of Carbon Fiber-Reinforced Plastic Composites

Factor Analysis of Machining Parameters of Fiber-Reinforced Polymer Composites Based on Finite Element Simulation with Experimental Investigation

Chip Formation Mechanism in Machining of Carbon Fiber Reinforced Plastic

Study on Cutting Force Performance and Cutting Mechanism of Carbon Fiber Reinforced Polymer (CFRP) Composites

Numerical Simulation on Mechanical Properties and Damage Behavior of CFRP with Self-Healing Microvascular Channels

Analysis of Burr and Tear in Milling of Carbon Fiber Reinforced Plastic (CFRP) Using Finite Element Method

The Interaction Between the Cutting Force and Induced Sub-Surface Damage in Machining of Carbon Fiber-Reinforced Plastics

Delamination and Chip Breaking Mechanism of Orthogonal Cutting CFRP/Ti6Al4V Composite