Abstract:Abstract Nickel-based alloy coatings were widely used for the remanufacturing of dies and moulds by laser cladding, but the crack sensitivity would be increase due to the higher strength and hardness, which reduced the wear resistance of Ni-based alloys. In this paper, Ni-based coatings with the addition of a plastic phase (an austenitic stainless net) were prepared using laser cladding technology, and the CeO 2 was added in cladding layers. The cracking mechanism, microhardness, microstructure, phase composition, and wear properties were investigated. The relationship between thermal stress and the elastic and plastic fracture had been developed from the standpoint of fracture mechanics and thermal elastic fracture mechanics. The fracture criterion of the nickel-based coating was obtained, and the study has shown that the crack sensitivity could be reduced by decreasing the thermal expansion coefficient Δ α . Thus, a new method was proposed, which the stainless steel nets were prefabricated on the substrate. It was found that the number of cracks reduced significantly with the addition of stainless steel net. When the stainless steel net with 14 mesh was added in Ni-based coatings, the average microhardness of nickel composite coating was 565 HV 0.2 , which was 2.6 times higher than that of the 45 steel substrate. Although the rare earth oxide 4 wt.% CeO 2 and stainless steel net were added in the Ni-based coating reducing the microhardness (the average microhardness is 425 HV 0.2 ), the wear resistance of it improved substantially. The wear volume of Ni-based composite coating was 0.56×10 −5 mm 3 ·N −1 ·m −1 , which was 85.1% lower than that of 45 steel. The experiment results have shown that the Nickel-based composite coating is equipped with low crack sensitivity and high abrasive resistance with austenitic stainless net and the rare earth oxide 4 wt.% CeO 2 . This research offers an efficient solution to produce components with low crack susceptibility and high wear-resistance coatings fabricated by laser cladding.

A Novel Grain Refinement Design to Inhibit Liquation Cracking in Laser Cladding Non-Weldable Nickel-Based Alloy

The role of shot peening on liquation cracking in laser cladding of K447A nickel superalloy powders over its non-weldable cast structure

Evolution behavior of liquid film in the heat-affected zone of laser cladding non-weldable nickel-based superalloy

Optimizing the Electrochemical Corrosion Performance of Laser Cladded Ni-based Single Crystal Superalloy Via Manipulation of Γ′(ni3al) Phase

The Suppression of Liquation Cracking in the Repair Process of Non-Weldable K447a Superalloys by Laser Surface Remelting-Assisted Laser Cladding

The role of the pulsed-wave laser characteristics on restraining hot cracking in laser cladding non-weldable nickel-based superalloy

Laser cladding repairing of directionally solidified nickel base superalloy and its tensile properties

A review on cracking mechanism and suppression strategy of nickel-based superalloys during laser cladding

Mechanism of High Temperature Mechanical Properties Enhancement of Ni-based Superalloys Repaired by Laser Directed Energy Deposition: Microstructure Analysis and Crystal Plasticity Simulation

Inhibition of Cracking by Grain Boundary Modification in a Non-Weldable Nickel-Based Superalloy Processed by Laser Powder Bed Fusion

Hot Crack Formation Mechanism and Inhibition of a Novel Cobalt-Based Alloy Coating during Laser Cladding

Cracking Behavior of Laser Cladding Forming Nickel Based Alloys

Crack Inhibition and Crystallographic Texture Control in an Additively Manufactured IN738LC Ni-based Superalloy

Liquefaction Characteristics and Cracking Behavior of the Grain Boundaries and Interdendritic Regions in Non-Weldable K447A Superalloy During Laser Re-Melting

Grain refinement and crack inhibition of hard-to-weld Inconel 738 alloy by altering the scanning strategy during selective laser melting

Study of Cracking Mechanism and Wear Resistance in Laser Cladding Coating of Ni-based Alloy

Laser Cladding Assisted by Friction Stir Processing for Preparation of Deformed Crack-Free Ni-Cr-Fe Coating with Nanostructure

Optimizing the electrochemical corrosion performance of laser cladded Ni-based single crystal superalloy via manipulation of γ′(Ni 3 Al) phase

Research on the Grain Boundary Liquation Mechanism in Heat Affected Zones of Laser Forming Repaired K465 Nickel-Based Superalloy

Additively manufactured crack-free nickel-based superalloys with synergistic strength and plasticity via grain refinement and striped oxides inhibition

HAZ Liquation Cracking Mechanism of IN-738LC Superalloy Prepared by Laser Solid Forming